CAN COMMUNICATION SYSTEM(for RHD) Lane Departure Warning Camera Communication Stop Mode

DTC Code DTC Name
Lane Departure Warning Camera Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Lane Departure Warning Camera Communication Stop Mode

Either condition is met:

  • "Front Camera Module" is not displayed on "CAN Bus Check".

    Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "Lane Departure Warning Camera Communication Stop Mode" in "DTC Combination Table".

    Click hereClick here

  • Power source or inside lane departure warning camera

  • Lane departure warning camera CAN branch wire or connector

  • Lane departure warning camera

  • Engine stop and start ECU*

*: w/ Stop and Start System

  • For vehicles with a lane departure alert system.

WIRING DIAGRAM

C278741E02

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click hereClick hereClick here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • DTC check procedure: Turn the ignition switch to ON and wait at least 51 seconds.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick here

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS WIRE (LANE DEPARTURE WARNING CAMERA CAN BRANCH WIRE)

    1. C268302C01

      *a

      Front view of wire harness connector

      (to Lane Departure Warning Camera)

      Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the lane departure warning camera connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q13-6 (CA1P) - Q13-12 (CA1N)

      Cable disconnected from negative (-) battery terminal

      54 to 69 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE LANE DEPARTURE WARNING CAMERA CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

    OK

  2. CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - BODY GROUND)

    1. C268302C02

      *a

      Front view of wire harness connector

      (to Lane Departure Warning Camera)

      Connect the cable to the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click hereClick hereClick here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q13-11 (GND) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - BATTERY)

    1. C268302C03

      *a

      Front view of wire harness connector

      (to Lane Departure Warning Camera)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      Q13-7 (IGB) - Body ground

      Ignition switch ON

      11 to 14 V

    Result

    Proceed to

    OK

    NG (w/o Stop and Start System)

    NG (w/ Stop and Start System)
    OK

    REPLACE LANE DEPARTURE WARNING CAMERA

    Click here

    NG (w/o Stop and Start System)

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    NG (w/ Stop and Start System)

  4. CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - ENGINE STOP AND START ECU)

    1. Disconnect the G87 engine stop and start ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q13-7 (IGB) - G87-12 (IGO1)

      Always

      Below 1 Ω

      Q13-7 (IGB) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE ENGINE STOP AND START ECU

    Click hereClick here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR