LIGHTING SYSTEM, Diagnostic DTC:B2439, B243A

DTC Code DTC Name
B2439 Headlamp LH Circuit
B243A Headlamp RH Circuit

DESCRIPTION

A DTC is stored when the headlight ECU sub-assembly receives a light source malfunction signal from its respective headlight unit. The headlight ECU sub-assembly LH stores DTC B2439 or B243A.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2439 Headlamp LH Circuit headlight ECU sub-assembly LH light source malfunction

  • Headlight unit assembly LH

  • Headlight ECU sub-assembly LH

 -
B243A Headlamp RH Circuit headlight ECU sub-assembly RH light source malfunction

  • Headlight unit assembly RH

  • Headlight ECU sub-assembly RH

 -

WIRING DIAGRAM

A001SCWE01
*a Lo/Hi Beam
*b Headlight Unit Assembly
*c Headlight ECU Sub-assembly

CAUTION / NOTICE / HINT

Note

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Turn the ignition switch to ON.

    2. Operate the light control switch to turn on the low beam headlights.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B2439 and B243A are not output.
      Result
      Result Proceed to
      OK A
      NG (DTC B2439 is output) B
      NG (DTC B243A is output) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    REPLACE HEADLIGHT UNIT ASSEMBLY RH Click here

    B

  3. REPLACE HEADLIGHT UNIT ASSEMBLY LH


    1. Replace the headlight unit assembly LH with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  5. CHECK FOR DTC


    1. Turn the ignition switch to ON.

    2. Operate the light control switch to turn on the low beam headlights.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B2439 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (HEADLIGHT UNIT ASSEMBLY LH WAS DEFECTIVE)

    NG

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH Click here

  6. REPLACE HEADLIGHT UNIT ASSEMBLY RH


    1. Replace the headlight unit assembly RH with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  8. CHECK FOR DTC


    1. Turn the ignition switch to ON.

    2. Operate the light control switch to turn on the low beam headlights.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B243A is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (HEADLIGHT UNIT ASSEMBLY RH WAS DEFECTIVE)

    NG

    REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH Click here