REAR DOOR(for Hatchback, Wagon) ADJUSTMENT

CAUTION / NOTICE / HINT

B332382C01

*a

Centering Bolt

*b

Standard Bolt
Tip:

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

  • Specified torque for standard bolts is shown in the standard bolt chart.

    Click here

PROCEDURE

  1. INSPECT REAR DOOR (for Hatchback)

    1. Check that the clearance measurements of areas "a" through "o" are within each standard range.

      B333987N01
      Table 1. Standard Clearance

      Area

      Measurement

      Area

      Measurement

      a

      3.9 to 6.9 mm (0.154 to 0.272 in.)

      b

      7.5 to 10.5 mm (0.295 to 0.413 in.)

      c

      3.9 to 6.9 mm (0.154 to 0.272 in.)

      d

      6.6 to 9.6 mm (0.260 to 0.378 in.)

      e

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      f

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      g

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      h

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      i

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      j

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      k

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      l

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      m

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      n

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      o

      3.0 to 7.0 mm (0.118 to 0.276 in.)

      -

      -

  2. INSPECT REAR DOOR (for Wagon)

    1. Check that the clearance measurements of areas "a" through "o" are within each standard range.

      B338686N01
      Table 2. Standard Clearance

      Area

      Measurement

      Area

      Measurement

      a

      4.05 to 7.05 mm (0.159 to 0.278 in.)

      b

      7.8 to 10.8 mm (0.307 to 0.425 in.)

      c

      4.05 to 7.05 mm (0.159 to 0.278 in.)

      d

      6.5 to 9.5 mm (0.256 to 0.374 in.)

      e

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      f

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      g

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      h

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      i

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      j

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      k

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      l

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      m

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      n

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      o

      3.0 to 7.0 mm (0.118 to 0.276 in.)

      -

      -

  3. ADJUST REAR DOOR

    Note:

    Make sure to turn the ignition switch off when adjusting door lock strikers.

    Tip:

    Use the same procedure for the hatchback and wagon.

    1. B327770

      Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

      09812-00010

    2. Tighten the hinge bolts on the vehicle body after the adjustment.

      26 N*m

      265 kgf*cm

      19 ft.*lbf

    3. Loosen the hinge bolts on the door and adjust the door position.

    4. Tighten the hinge bolts on the door after the adjustment.

      26 N*m

      265 kgf*cm

      19 ft.*lbf

    5. B327771

      Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

    6. Using a brass bar and a hammer, hit the striker to adjust its position.

    7. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

      23 N*m

      235 kgf*cm

      17 ft.*lbf