BLIND SPOT MONITOR SYSTEM SYSTEM DESCRIPTION

  1. GENERAL

  2. FUNCTION OF COMPONENTS

    • *1: for LHD

    • *2: for RHD

    Component

    Function

    Blind Spot Monitor Sensor

    • Consists of a 24 GHz radar module and an integrated processing module.

    • Illuminates or blinks the outer rear view mirror indicator on the outer rear view mirror assembly.

    • Changes the outer rear view mirror indicator on the outer rear view mirror assembly from illuminated to blinking when a turn signal switch operation signal is received from the combination meter assembly with the blind spot monitor function operating.

    • Sends the signal to the outer rear view mirror indicator on the outer rear view mirror assembly.

    • Dims the outer rear view mirror indicator on the outer rear view mirror assembly and blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2).

    • Turns on the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is on.

    Outer Rear View Mirror Assembly

    • Outer Rear View Mirror (Outer Rear View Mirror Indicator)

    Turns on or blinks the indicator based on a signal from the blind spot monitor sensor.

    Blind Spot Monitor Main Switch (Warning Cancel Switch Assembly*1 or Telltale light Assembly*2)

    • Blind Spot Monitor Indicator

    • Turns the blind spot monitor system on or off.

    • Informs the state of the blind spot monitor system by illuminating the blind spot monitor indicator.

    Combination Meter Assembly

    • Multi-information Display

    • Sends a turn signal switch operation signal from the headlight dimmer switch assembly to the blind spot monitor sensor via CAN communication.

    • Displays an error message on the multi-information display if the blind spot monitor detects a malfunction while it is operating.

    Main Body ECU (Multiplex Network Body ECU)

    Sends the destination information and the dimmer signal to the blind spot monitor sensor via CAN communication.

    Brake Actuator Assembly

    • Skid Control ECU

    Transmits a vehicle speed signal to the blind spot monitor sensor via CAN communication.

    ECM

    Sends a shift position signal (R) to the blind spot monitor sensor via CAN communication.

    Spiral with Sensor Cable Sub-assembly

    Detects the angle of the steering wheel and sends the resulting signals to the blind spot monitor sensor via CAN communication.

  3. OPERATION DESCRIPTION

    1. Operation description of the blind spot monitor system

      1. Operation conditions

        • The blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is on.

          • *1: for LHD

          • *2: for RHD

        • Vehicle speed is more than approximately 40 km/h (25 mph).

      2. Conditions in which a sensor can detect a vehicle

        The blind spot monitor system indicates detection of a vehicle in the detection area when either condition is met:

        • When a vehicle is detected in an adjacent lane overtaking this vehicle.

        • When a vehicle is detected entering the detection area because it changed lanes.

      3. E274261C02

        *a

        Vehicles in the following areas can be detected

        *b

        Within approximately 3.5 m (11.49 ft) from the side of the vehicle

        *c

        Within approximately 0.5 m (1.64 ft) from the side of the vehicle

        *d

        Within approximately 3 m (9.85 ft) behind the rear bumper

        *e

        Within approximately 1 m (3.29 ft) forward of the rear bumper

        Detection area

        Vehicles in the following areas can be detected:

  4. OPERATION OF OUTER REAR VIEW MIRROR INDICATOR

    • *1: for LHD

    • *2: for RHD

    1. Initial check

      1. When the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is turned on with the ignition switch on, the outer rear view mirror indicator on each outer rear view mirror assembly illuminates for 3 seconds.

      2. When the ignition switch is turned from off to on with the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on, the outer rear view mirror indicator on each outer rear view mirror assembly illuminates for 3 seconds.

    2. E270861E01

      Operation for the blind spot monitor function

      1. Operation for blind spot monitor function

        • When a sensor detects a vehicle in the blind spot area, the outer rear view mirror indicator on the outer rear view mirror assembly illuminates.

        • While the sensor is detecting a vehicle in the detection area and the indicator is illuminated, if the turn signal switch is operated, the outer rear view mirror indicator on the outer rear view mirror assembly starts blinking as shown in the illustration.

  • The blind spot monitor system is a function that assists the driver in making the decision to change lanes. The function uses quasi-millimeter wave radar to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outer rear view mirror assembly. The function advises the driver of the existence of a vehicle by illuminating the outer rear view mirror indicator on the outer rear view mirror assembly.

  • If the turn signal switch is operated while the outer rear view mirror indicator on an outer rear view mirror assembly is illuminated, the indicator starts blinking to give additional warning to the driver.