ENTRY AND START SYSTEM(for Start Function) Engine does not Start

DTC Code DTC Name
Engine does not Start

DESCRIPTION

The push-button start function uses a push-type engine switch, which the driver can operate by merely carrying the key. This system consists primarily of the power management control ECU, engine switch, ID code box, steering lock ECU, key, ACC relay, IG1 relay, IG2 relay and certification ECU. The power management control ECU controls the system. This function operates in cooperation with the entry and start system.

WIRING DIAGRAM

  • Refer to SFI system*1 or ECD system*2 (Starter Signal Circuit):

  • *1: for ZR Series Engine

  • *2: for 1WW Engine

CAUTION / NOTICE / HINT

Note:

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

  • Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

After the certification ECU, steering lock actuator assembly (steering lock ECU) and/or ID code box are/is replaced, perform the registration procedures described in the Service Bulletin.

  1. EMERGENCY ENGINE START CONTROL

    A214063E02

    1. To operate the push-button start function when the key battery is low, hold the key against to the engine switch with the brake pedal*1 or clutch pedal*2 depressed.

      *1: except Manual Transaxle

      *2: for Manual Transaxle

      Table 1. Text in Illustration

      *1

      Engine Switch

      *2

      Key

PROCEDURE

  1. CHECK IF ENGINE START (INITIALIZE STEERING LOCK)

    1. Place the key on the seat. Move the shift lever to P*1 and depress the brake pedal*1 or clutch pedal*2.

      *1: except Manual Transaxle

      *2: for Manual Transaxle

    2. Check that the engine switch indicator is illuminated in green, push the engine switch, and check that the engine starts.

    3. Open and close the driver side door with the engine switch off.

    4. Check if the engine can be started.

      OK

      Engine can be started.

    Tip:

    After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure.

    USE SIMULATION METHOD TO CHECK

    (Click here)

  2. READ VALUE USING INTELLIGENT TESTER (POWER SUPPLY OPEN) AND CHECK FOR DTC

    1. Read value using the intelligent tester (Power Supply Open).

      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry&Start / Data List.

      5. According to the display on the intelligent tester, read the Data List.

        Table 2. Entry&Start

        Tester Display

        Measurement Item/Range

        Normal Condition

        Diagnostic Note

        Power Supply Open

        Power supply open / OK or NG (Past)

        OK: Power supply normal

        NG (Past): Power supply open occurred in past

        -

    2. Check for DTCs

      1. Enter the following menus: Body / (desired system) / DTC.

      2. Read the DTCs.

        Table 3. Result

        Result

        Proceed to

        No DTC is output, power supply open has not occurred in past

        A

        DTCs other than B2782 are output

        B

        Power supply open has occurred in past and/or DTC B2782 is output

        C

    GO TO DTC CHART

    (Click here)

    GO TO STEERING LOCK SYSTEM (B2782)

    (Click here)

  3. CHECK ENGINE SWITCH CONDITION

    1. Check if the power source mode changes.

      1. When the key is inside the vehicle and the shift lever is in P*, push the engine switch and check that the power source mode changes.

        *: except Manual Transaxle

        Table 4. Result

        Result

        Proceed to

        OK: off → on (ACC) → on (IG) → off

        A

        Power source mode does not change to on (IG) or on (ACC).

        B

        Power source mode does not change to on (IG).

        C

        Power source mode does not change to on (ACC).

        D

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG AND ACC)

    (Click here)

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG)

    (Click here)

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (ACC)

    (Click here)

  4. CHECK CRANKING FUNCTION

    1. Check the engine cranking function.

      1. except Manual Transaxle: When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in P, check that depressing the brake pedal and pressing the engine switch cranks the engine.

      2. for Manual Transaxle: When there is fuel in the fuel tank and the key is inside the vehicle, check that depressing the clutch pedal and pressing the engine switch cranks the engine.

        OK

        Engine cranks.

        Table 5. Result

        Result

        Proceed to

        OK (for ZR Series Engine)

        A

        OK (for 1WW Engine)

        B

        NG

        C
        Tip:

        • for 1ZR-FAE:

          • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

        • for 2ZR-FAE:

          • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

        • for 1WW:

          • If it is necessary to refer to the ECD system, refer to the following procedure (Click here).

    GO TO SFI SYSTEM

    GO TO ECD SYSTEM

  5. INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

    1. except Manual Transaxle:

      1. A125187E24

        Disconnect the C23 park/neutral position switch connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        4 (B) - 9 (L)

        Shift lever in P or N

        Below 1 Ω

        Shift lever not in P or N

        10 kΩ or higher
        Table 6. Text in Illustration

        *1

        Component without harness connected

        (Park/Neutral Position Switch)

    2. for Manual Transaxle:

      1. A129222E29

        Disconnect the A4 clutch start switch connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        1 - 2

        Pushed in

        (Clutch pedal depressed)

        Below 1 Ω

        Released

        (Clutch pedal released)

        10 kΩ or higher

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ST RELAY, PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCHClick here

  6. INSPECT ST RELAY

    B016200

    1. Remove the ST relay from the No. 3 relay block.

    2. Measure the resistance according value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3 - 5

      When battery voltage is not applied to terminals 1 and 2

      10 kΩ or higher

      When battery voltage is applied to terminals 1 and 2

      Below 1 Ω

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ST RELAY, PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCHClick here

  7. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

    U121701E02

    1. Disconnect the H70 power management control ECU connector.

    2. except Manual Transaxle

      Move the shift lever to P or N.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      H70-3 (STAR) - Body ground

      20°C (68°F)

      93.8 to 136.3 Ω
      Table 7. Text in Illustration

      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ST RELAY, PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCHClick here

  8. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH OR CLUTCH START SWITCH)

    1. except Manual Transaxle:

      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Power Source Control / Data List.

      5. According to the display on the intelligent tester, read the Data List.

        Table 8. Power Source Control

        Tester Display

        Measurement Item/Range

        Normal Condition

        Diagnostic Note

        Stop Light Switch1

        Stop light switch 1 / ON or OFF

        ON: Brake pedal depressed

        OFF: Brake pedal released

        -

        OK

        ON (brake pedal depressed) or OFF (brake pedal released) appears on the screen according to the condition of the brake pedal.

    2. for Manual Transaxle:

      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Power Source Control / Data List.

      5. According to the display on the intelligent tester, read the Data List.

        Table 9. Power Source Control

        Tester Display

        Measurement Item/Range

        Normal Condition

        Diagnostic Note

        Neutral SW/Clutch SW

        Status of the clutch start switch/ ON or OFF

        ON: Clutch pedal depressed

        OFF: Clutch pedal released

        -

        OK

        ON (clutch pedal depressed) or OFF (clutch pedal released) appears on the screen according to the condition of the clutch pedal.

        Table 10. Result

        Result

        Proceed to

        OK

        A

        NG (except Manual Transaxle)

        B

        NG (for Manual Transaxle, LHD)

        C

        NG (for Manual Transaxle, RHD)

        D

    CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)Click here

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

  9. READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Table 11. Power Source Control

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Steering Unlock Switch

      Steering unlock switch / ON or OFF

      ON: Steering lock released

      OFF: Steering lock locked

      -

      OK

      ON (steering lock released) or OFF (steering lock locked) appears on the screen according to the steering lock condition.

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU)Click here

  10. CHECK STEERING LOCK

    1. Turn the engine switch from off to on (ACC) and check that the steering lock moves to the released position when the engine switch is on (ACC).

      OK

      Lock moves to released position.

    GO TO STEERING LOCK SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

    (Click here)

  11. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the intelligent tester on.

      Tip:

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    3. Enter the following menus: Body / Entry&Start / Data List.

    4. According to the display on the intelligent tester, read the Data List.

    5. Turn the engine switch on (IG).

      Table 12. Entry&Start

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Engine Start Request

      Start request signal response / OK or NG

      OK: Received

      NG: Not received

      -

      OK

      OK appears on the screen.

    REPLACE CERTIFICATION ECU

  12. READ VALUE USING INTELLIGENT TESTER (L CODE)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the intelligent tester on.

      Tip:

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    3. Enter the following menus: Body / Entry&Start / Data List.

    4. According to the display on the intelligent tester, read the Data List.

    5. Turn the engine switch on (IG).

      Table 13. Entry&Start

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      L Code Check

      L code certification result / OK or NG

      OK: L code certification result normal

      NG: L code certification result abnormal

      -

      OK

      OK (L code certification result normal) appears on the screen.

    GO TO ENGINE IMMOBILISER SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

    (Click here)

  13. READ VALUE USING INTELLIGENT TESTER (S CODE)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the intelligent tester on.

      Tip:

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    3. Enter the following menus: Body / Entry&Start / Data List.

    4. According to the display on the intelligent tester, read the Data List.

    5. Turn the engine switch on (IG).

      Table 14. Entry&Start

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      S Code Check

      S code certification result / OK or NG

      OK: S code certification result normal

      NG: S code certification result abnormal

      -

      OK

      OK (S code certification result normal) appears on the screen.

    GO TO ENGINE IMMOBILISER SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

    (Click here)

  14. READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the intelligent tester on.

      Tip:

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    3. Enter the following menus: Body / Power Source Control / Data List.

    4. According to the display on the intelligent tester, read the Data List.

    5. Turn the engine switch on (IG).

      Table 15. Power Source Control

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Starter Request Signal

      Starter request signal monitor / ON or OFF

      ON: ST relay on

      OFF: ST relay off

      except Manual Transaxle:

      The engine switch is pressed and hold with the shift lever in P or N.

      for Manual Transaxle:

      The engine switch is pressed and held.
      Note:

      Check that the engine switch indicator is illuminated in green and push the engine switch.

      OK

      The Data List item changes from OFF to ON when the engine switch is pushed.

      Table 16. Result

      Result

      Proceed to

      OK (for ZR Series Engine)

      A

      OK (for 1WW Engine)

      B

      NG (for LHD)

      C

      NG (for RHD)

      D
      Tip:

      • for 1ZR-FAE:

        • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

      • for 2ZR-FAE:

        • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

      • for 1WW:

        • If it is necessary to refer to the ECD system, refer to the following procedure (Click here).

    GO TO SFI SYSTEM

    GO TO ECD SYSTEM

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

  15. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

    Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  16. INSPECT STOP LIGHT SWITCH

    1. Inspect the stop light switch assembly (Click here).

      Table 17. Result

      Result

      Proceed to

      OK (for LHD)

      A

      OK (for RHD)

      B

      NG

      C

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE STOP LIGHT SWITCH

    (Click here)

  17. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU)

    Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  18. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

    1. U122733E02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      H54-4 (SLP1) - Body ground

      Steering lock locked

      10 kΩ or higher

      H54-4 (SLP1) - Body ground

      Steering lock released

      Below 1 Ω
      Table 18. Text in Illustration

      *1

      Component with harness connected

      (Steering Lock ECU)
      Table 19. Result

      Result

      Proceed to

      OK (for LHD)

      A

      OK (for RHD)

      B

      NG

      C

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

    (Click here)

  19. REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ST RELAY, PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

    1. Replace the ST relay, park/neutral position switch or clutch start switch with a new or normally functioning part, or repair or replace any damaged wire harness or connector.

  20. READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

    1. Connect the intelligent tester to the DLC3.

    2. Turn the intelligent tester on.

      Tip:

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    3. Enter the following menus: Body / Power Source Control / Data List.

    4. According to the display on the intelligent tester, read the Data List.

    5. Turn the engine switch on (IG).

      Table 20. Power Source Control

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Starter Request Signal

      Starter request signal monitor / ON or OFF

      ON: ST relay on.

      OFF: ST relay off.

      except Manual Transaxle:

      The engine switch is pressed and hold with the shift lever in P or N.

      for Manual Transaxle:

      The engine switch is pressed and held.
      Note:

      Check that the engine switch indicator is illuminated in green and push the engine switch.

      OK

      The Data List item changes from OFF to ON when the engine switch is pushed.

      Table 21. Result

      Result

      Proceed to

      OK

      A

      NG (for LHD)

      B

      NG (for RHD)

      C

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

    REPLACE POWER MANAGEMENT CONTROL ECU

    (Click here)

  21. CHECK IF ENGINE STARTS

    1. Place the key on the seat. Move the shift lever to P*1 and depress the brake pedal*1 or clutch pedal*2.

      • *1: except Manual Transaxle

      • *2: for Manual Transaxle

    2. Check that the engine switch indicator is illuminated in green, push the engine switch, and check that the engine starts.

    3. Open and close the driver side door with the engine switch off.

    4. Check if the engine can be started.

      OK

      Engine can be started.

      Table 22. Result

      Result

      Proceed to

      OK

      A

      NG (for ZR Series Engine)

      B

      NG (for 1WW Engine)

      C
      Tip:

      • After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure.

      • for 1ZR-FAE:

        • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

      • for 2ZR-FAE:

        • If it is necessary to refer to the SFI system, refer to the following procedure (Click here).

      • for 1WW:

        • If it is necessary to refer to the ECD system, refer to the following procedure (Click here).

    END

    GO TO SFI SYSTEM

    GO TO ECD SYSTEM