FRONT SHOCK ABSORBER INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE

  1. INSTALL FRONT SHOCK ABSORBER ASSEMBLY LH (for Integrated Input Construction Type)

    1. C188480C05

      *a

      Positioning Pin

      *b

      Depression

      Install the front coil spring lower insulator to the front shock absorber assembly.

      Note:

      When installing the insulator, fit the insulator into the depression of the spring seat and insert the positioning pin into the hole.

    2. Install the front spring bumper to the front shock absorber assembly.

      Note:

      Position the end of the front spring bumper with the smaller diameter downward.

    3. C266190N01

      Secure SST in a vise.

      09727-30021

      09727-00010

      09727-00021

      09727-00031

    4. C275706C08

      *a

      Correct

      *b

      Incorrect

      Attach the arm of SST to the diameter of the coil spring.

      CAUTION:

      • Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

      • Make sure that the claws of the hooks are securely attached.

    5. Using SST, compress the coil spring.

      CAUTION:

      • If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

      • Do not compress the spring until the coil springs contact each other.

      • Do not use an impact wrench.

    6. C267394C01

      *1

      Spring Lower Seat

      Install the front coil spring so that the end comes to the stepped portion of the spring lower seat.

    7. Install the front coil spring upper insulator.

    8. Install the front coil spring upper seat.

    9. Install the front suspension support sub-assembly to the front shock absorber assembly.

      Note:

      When installing the front suspension support sub-assembly, align the cutout on the front suspension support sub-assembly with the end of the shock absorber piston rod.

    10. C188476

      Temporarily install a new front support to front shock absorber nut.

    11. Remove SST from the front coil spring.

      Note:

      Do not use an impact wrench. It will damage SST.

  2. INSTALL FRONT SHOCK ABSORBER ASSEMBLY LH (for Separate Input Construction Type)

    1. C188480C06

      *a

      Positioning Pin

      *b

      Depression

      Install the front coil spring lower insulator to the front shock absorber assembly.

      Note:

      When installing the insulator, fit the insulator into the depression of the spring seat and insert the positioning pin into the hole.

    2. Install the front spring bumper to the front shock absorber assembly.

      Note:

      Position the end of the front spring bumper with the smaller diameter downward.

    3. C266190N02

      Secure SST in a vise.

      09727-30021

      09727-00010

      09727-00021

      09727-00031

    4. C275706C09

      *a

      Correct

      *b

      Incorrect

      Attach the arm of SST to the diameter of the coil spring.

      CAUTION:

      • Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

      • Make sure that the claws of the hooks are securely attached.

    5. Using SST, compress the coil spring.

      CAUTION:

      • If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

      • Do not compress the spring until the coil springs contact each other.

      • Do not use an impact wrench.

    6. C267394C02

      *1

      Spring Lower Seat

      Install the front coil spring so that the end comes to the stepped portion of the spring lower seat.

    7. Install the front coil spring upper insulator.

    8. Install the front coil spring upper seat.

    9. C207004C01

      *a

      Upper Side

      *b

      Lower Side

      Install the strut mounting bearing.

      Note:

      Do not install the bearing upside down.

    10. Install the front suspension support sub-assembly to the front shock absorber assembly.

      Note:

      When installing the front suspension support sub-assembly, align the cutout on the front suspension support sub-assembly with the end of the shock absorber piston rod.

    11. Install the collar to the front shock absorber assembly.

    12. C188476

      Temporarily install a new front support to front shock absorber nut.

    13. Remove SST from the front coil spring.

      Note:

      Do not use an impact wrench. It will damage SST.

  3. INSTALL FRONT SUSPENSION SUPPORT PLATE LH

    1. Install the front suspension support plate to the front shock absorber with coil spring.

  4. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

    1. Install the front shock absorber with coil spring (upper side) and front fender apron rear extension LH with the 3 nuts.

      50 N*m

      510 kgf*cm

      37 ft.*lbf

    2. Connect the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

      240 N*m

      2447 kgf*cm

      177 ft.*lbf

      Tip:

      The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.

    3. Tighten the front support to front shock absorber nut.

      47 N*m

      479 kgf*cm

      35 ft.*lbf

  5. CONNECT FRONT FLEXIBLE HOSE

    1. Connect the front flexible hose to the steering knuckle with the bolt.

      18.5 N*m

      189 kgf*cm

      14 ft.*lbf

  6. CONNECT FRONT SPEED SENSOR LH

    1. Connect the front flexible hose and front speed sensor with the bolt.

      18.5 N*m

      189 kgf*cm

      14 ft.*lbf

      Note:

      Do not twist the front speed sensor when installing it.

      Tip:

      Install the front flexible hose and wire harness bracket of the front speed sensor in that order.

  7. CONNECT FRONT STABILIZER LINK ASSEMBLY LH

    1. C149537

      Connect the front stabilizer link assembly to the front shock absorber with coil spring with the nut.

      74 N*m

      755 kgf*cm

      55 ft.*lbf

      Tip:

      If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

  8. INSTALL FRONT SUSPENSION SUPPORT DUST COVER LH

    1. Install the front suspension support dust cover LH.

  9. INSTALL FRONT WHEEL

    103 N*m

    1050 kgf*cm

    76 ft.*lbf

  10. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click hereClick hereClick here