Note
As the door control battery is installed between the vehicle battery and main body ECU (instrument panel junction block assembly), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (instrument panel junction block assembly) before performing this troubleshooting procedure Click here.
Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | See page |
|---|---|---|
| Entire combination meter does not operate | Refer to "Entire Combination Meter does not Operate" | |
| Meter illumination is always dark | Refer to "Meter Illumination is Always Dark" | |
| Multi-information display does not change using steering pad switch assembly | Read the Data List [Multi Switch (UP), Multi Switch (Down), Multi Switch (Menu), Multi Switch (ENTER), Multi Switch (Right) or Multi Switch (Left)] (for Multi-information Display [Color Type]) | |
| Read the Data List [Multi Display Select Switch] (for Multi-information Display [Monochrome Type]) | ||
| Steering pad switch assembly | ||
| Spiral with sensor cable sub-assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| DTCs display malfunction (Other systems operate normally) | Combination meter assembly | |
| "ODO/TRIP meter" display malfunction | Combination meter assembly | |
| Other systems that use the speed signal do not operate normally | Proceed to "Speed signal Circuit" |
| Symptom | Suspected Area | See page |
|---|---|---|
| Speedometer malfunction | Refer to "Speedometer Malfunction" | |
| Tachometer malfunction | Refer to "Tachometer Malfunction" | |
| Fuel receiver gauge malfunction | Refer to "Fuel Receiver Gauge Display Malfunction" | |
| Engine coolant temperature receiver gauge malfunction | Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" |
| Symptom | Suspected Area | See page |
|---|---|---|
| High beam indicator light malfunction | CAN communication system | |
| Lighting system | ||
| Perform Active Test [Indicat. Lamp Beam] | ||
| Combination meter assembly | ||
| Taillight indicator light malfunction | CAN communication system | |
| Lighting system | ||
| Perform Active Test [Indicat. Lamp Tail] | ||
| Combination meter assembly | ||
| Front fog indicator light malfunction (w/ Front Fog Light) | CAN communication system | |
| Lighting system | ||
| Perform Active Test [Indicat. Lamp Fr FOG] | ||
| Combination meter assembly | ||
| Rear fog indicator light malfunction | CAN communication system | |
| Lighting system | ||
| Perform Active Test [Indicat. Lamp Rr Fog] | ||
| Combination meter assembly | ||
| SRS warning light malfunction | Check LED | |
| CAN communication system | ||
| Airbag system | ||
| Perform Active Test [Indicat. Lamp Airbag] | ||
| Combination meter assembly | ||
| Seat belt warning light malfunction | CAN communication system | |
| Seat belt warning system | ||
| Perform Active Test [Front Passenger Side Seat Belt] | ||
| Perform Active Test [Driver Side Seat Belt] | ||
| Combination meter assembly | ||
| Parking brake warning light malfunction | Electric parking brake system | |
| Perform Active Test [Indicat. Park] | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| Parking brake auto off indicator light malfunction | Electric parking brake system | |
| Perform Active Test [EPB Auto OFF Indicator] | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| Brake warning light (Yellow indicator) malfunction | Check LED | |
| CAN communication system | ||
| Vehicle stability control system | ||
| Perform Active Test [Indicat. Lamp ECB] | ||
| Combination meter assembly | ||
| Brake warning light (Red indicator) malfunction | Check LED | |
| CAN communication system | ||
| Vehicle stability control system | ||
| Perform Active Test [Indicat. Lamp Brake] | ||
| Combination meter assembly | ||
| ABS warning light malfunction | Check LED | |
| CAN communication system | ||
| Vehicle stability control system | ||
| Perform Active Test [Indicat. Lamp ABS] | ||
| Combination meter assembly | ||
| Slip indicator light malfunction | Check LED | |
| CAN communication system | ||
| Vehicle stability control system | ||
| Perform Active Test [Indicat. Lamp Slip] | ||
| Combination meter assembly | ||
| VSC OFF indicator light malfunction | Check LED | |
| CAN communication system | ||
| Vehicle stability control system | ||
| Perform Active Test [Indicat. VSC OFF] | ||
| Combination meter assembly | ||
| EPS warning light malfunction | CAN communication system | |
| Power steering system | ||
| Perform Active Test [Indicat. EPS] | ||
| Combination meter assembly | ||
| Automatic high beam indicator light malfunction (w/ Automatic High Beam System) | CAN communication system | |
| Automatic high beam system | ||
| Perform Active Test [Automatic High Beam Indicator] | ||
| Combination meter assembly | ||
| Fuel warning light malfunction (Fuel receiver gauge operates normally) | Perform Active Test [Indicat. Lamp Fuel] | |
| Combination meter assembly | ||
| MIL (Malfunction indicator lamp) malfunction | ECD system (for 1WW) | |
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| Harness or connector | - | |
| Master warning light malfunction | CAN communication system | |
| Perform Active Test [Master Warning] | ||
| Combination meter assembly | ||
| SIL indicator light (Up/Down) malfunction | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Perform Active Test [Indicat. SIL (Up)] | ||
| Perform Active Test [Indicat. SIL (Down)] | ||
| Combination meter assembly | ||
| Cruise indicator light malfunction (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Perform Active Test [Indicat. Lamp Cruise] | ||
| Combination meter assembly | ||
| SET indicator light malfunction (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| Perform Active Test [Indicat. SET] | ||
| Combination meter assembly | ||
| Speed limiter indicator light malfunction (w/ Speed Limiter System) | CAN communication system | |
| Speed limiter system | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Perform Active Test [Indicat. ASL] | ||
| Combination meter assembly | ||
| Tire pressure warning light malfunction (w/ Tire Pressure Warning System) | Check LED | |
| Tire pressure warning system | ||
| Perform Active Test [Indicat. Tire Pressure Warning System] | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Lane departure alert indicator light malfunction (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| Pre-crash safety indicator light malfunction (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| AFS OFF indicator light malfunction (w/ AFS) | CAN communication system | |
| Lighting system | ||
| Headlight swivel ECU assembly | ||
| Combination meter assembly | ||
| Turn indicator light malfunction | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | |
| Read the Data List [Turn Signal Switch (Right), Turn Signal Switch (Left), Turn Switch Signal (Full Turn), Hazard Flasher Switch] | ||
| Hazard warning signal switch assembly | ||
| Headlight dimmer switch assembly | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| Glow indicator light malfunction | CAN communication system | |
| Perform Active Test [Indicat. GLOW] | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| Stop and start indicator light malfunction | Check LED | |
| CAN communication system | ||
| Perform Active Test [Stop and Start ON Indicator] | ||
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly | ||
| Stop and start cancel indicator light malfunction | Check LED | |
| CAN communication system | ||
| Perform Active Test [Stop and Start OFF Indicator] | ||
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | |
| "Ending" display malfunction | Combination meter assembly | |
| "Current fuel consumption" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (Range)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Average speed (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Distance (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "Other (Blank)" display malfunction | Combination meter assembly | |
| "Outside temp" display malfunction | Cooler (ambient temperature sensor) thermistor | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Icy street warning" display malfunction | Cooler (ambient temperature sensor) thermistor | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "Drive information tab" display malfunction | Combination meter assembly | |
| "Navigation tab" display malfunction (w/ Navigation System) | CAN communication system | |
| Navigation system | ||
| Combination meter assembly | ||
| Radio and display receiver assembly | ||
| "Audio tab" display malfunction (for Radio and Display Type) | CAN communication system | |
| Navigation system | ||
| Audio and visual system (for Radio and Display Type) | ||
| Combination meter assembly | ||
| Radio and display receiver assembly | ||
| Driving aids tab (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Road sign assist system (w/ Road Sign Assist System) | ||
| Lane departure alert system (w/ Lane Departure Alert System) | ||
| Combination meter assembly | ||
| Pre-crash safety city sensor | ||
| "Message tab" display malfunction | Combination meter assembly | |
| "Setting tab" display malfunction | Combination meter assembly | |
| "Each door ajar" display malfunction (Door courtesy switch, back door courtesy switch or hood courtesy switch is normal) | CAN communication system | |
| Combination meter assembly | ||
| Main body ECU (instrument panel junction block assembly) | - | |
| "DPF full, engine service required." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "DPF full. See owner's manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "DPF manual regeneration in process." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Oil Maintenance required soon." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Oil maintenance required." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Resetting oil maintenance data." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Resetting of oil maintenance data incomplete." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Drain water from fuel filter." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | Fuel filter assembly (for 1WW) | |
| Fuel filter assembly (for 2WW) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "Stop & Start system malfunction. Inspect at dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly | ||
| "Stop & Start system active. Shift to N and depress clutch to restart." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly | ||
| "Check cruise control system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "Cruise control displayed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "Check speed limiter system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Speed Limiter System) | CAN communication system | |
| Speed limiter system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "Speed limiter displayed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Speed Limiter System) | CAN communication system | |
| Speed limiter system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "ADJUSTING FRONT CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Check LDA system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "LDA system is unavailable below approx. 50km/h." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "LDA system is unavailable below approx. 32MPH." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "LDA System is unavailable at this speed." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Lane departure alert displayed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Lane Departure Alert System) | CAN communication system | |
| Lane departure alert system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "CHECKING PRE-CRASH BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "BRAKE!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Pre-crash safety display" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Check Pre-Crash Safety." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Pre-Crash Brake is disabled due to VSC OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Pre-Crash Safety temporarily not available." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Front sensor systems are temporarily unavailable due to inappropriate temp. Wait a moment." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Front sensor systems are temporarily unavailable due to blocked vision. Clean windshield." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Pre-Crash Safety OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Check RSA system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Road Sign Assist System) | CAN communication system | |
| Road sign assist system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Apply parking brake." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Release parking brake." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Shift to P position when parked." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Parking brake overheat." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Parking brake inoperable." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Check parking brake system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "Check power steering system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Power steering system | ||
| Power steering ECU assembly (for LHD) | ||
| Power steering ECU assembly (for RHD) | ||
| Combination meter assembly | ||
| "Shift to P position." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Key not detected." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Turn power off." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Key detected in vehicle." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Depress clutch pedal, Touch ENGINE switch with key." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Depress clutch pedal and push ENGINE switch to start." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Shift to P position to start." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Key battery low." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Auto power off to conserve battery." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Shift to P position and push ENGINE switch to turn power OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Check steering lock system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Steering lock system | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Steering lock active." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Steering lock system | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Check clutch switch." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "Headlight system malfunction. Visit your dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Lighting system | ||
| Automatic high beam system (w/ Automatic High Beam System) | ||
| Headlight leveling ECU assembly (for LHD, w/o AFS) | ||
| Headlight leveling ECU assembly (for RHD, w/o AFS) | ||
| Headlight swivel ECU assembly (w/ AFS) | ||
| Combination meter assembly | ||
| "Brake effectiveness is reduced due to failure, please stop in a safe area and check manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Vehicle stability control system | ||
| Brake actuator assembly (skid control ECU) | ||
| Combination meter assembly | ||
| "TRC OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Vehicle stability control system | ||
| Brake actuator assembly (skid control ECU) | ||
| Combination meter assembly | ||
| "Check charging system." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Engine oil pressure low." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "Turn lights OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Lighting system | ||
| Main body ECU (instrument panel junction block assembly) | - | |
| Combination meter assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| "OPENING" display malfunction | Combination meter assembly | |
| "ENDING" display malfunction | Combination meter assembly | |
| "CURRENT FUEL CONSUMPTION" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "AVERAGE FUEL CONSUMPTION" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "AVERAGE SPEED" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "ELAPSED TIME" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "SETTING" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "IDLING STOP TIME (AFTER START)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "TOTAL IDLING STOP TIME" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | |
| "OTHER (BLANK)" display malfunction | Combination meter assembly | |
| "OUTSIDE TEMP" display malfunction | Cooler (ambient temperature sensor) thermistor | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "ICY STREET WARNING" display malfunction | Cooler (ambient temperature sensor) thermistor | |
| Harness or connector | - | |
| Combination meter assembly | ||
| "EACH DOOR AJAR" display malfunction (Door courtesy switch, back door courtesy switch or hood courtesy switch is normal) | CAN communication system | |
| Combination meter assembly | ||
| Main body ECU (instrument panel junction block assembly) | - | |
| "DPF FULL, ENGINE SERVICE REQUIRED." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "DPF FULL. SEE OWNER'S MANUAL." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "DPF MANUAL REGENERATION IN PROCESS." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "OIL MAINTENANCE REQUIRED SOON." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "OIL MAINTENANCE REQUIRED." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "RESETTING OIL MAINTENANCE DATA." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "RESETTING OF OIL MAINTENANCE DATA INCOMPLETE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "DRAIN WATER FROM FUEL FILTER." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | Fuel filter assembly (for 1WW) | |
| Fuel filter assembly (for 2WW) | ||
| Harness or connector | - | |
| Combination meter assembly | ||
| "STOP & START SYSTEM MALFUNCTION. INSPECT AT DEALER." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly | ||
| "STOP & START SYSTEM ACTIVE. SHIFT TO N AND DEPRESS CLUTCH TO RESTART." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Stop and start system | ||
| Engine stop and start ECU | ||
| Combination meter assembly | ||
| "CHECK CRUISE CONTROL SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "Cruise control displayed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Cruise Control System) | CAN communication system | |
| Cruise control system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "CHECK SPEED LIMITER SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Speed Limiter System) | CAN communication system | |
| Speed limiter system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "Speed limiter displayed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Speed Limiter System) | CAN communication system | |
| Speed limiter system | ||
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| Combination meter assembly | ||
| "CHECKING PRE-CRASH BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "BRAKE!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "Pre-crash safety display" message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "CHECK PRE-CRASH SAFETY." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "PRE-CRASH BRAKE IS DISABLED DUE TO VSC OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "PRE-CRASH SAFETY TEMPORARILY NOT AVAILABLE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "FRONT SENSOR SYSTEMS ARE TEMP. UNAVAILABLE DUE TO INAPPROPRIATE TEMPERATURE. WAIT A MOMENT." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "FRONT SENSOR SYSTEMS ARE TEMP. UNAVAILABLE DUE TO BLOCKED VISION. CLEAN WINDSHIELD." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "PRE-CRASH SAFETY OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Pre-crash Safety System) | CAN communication system | |
| Pre-crash safety system | ||
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| "APPLY PARKING BRAKE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "RELEASE PARKING BRAKE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "SHIFT TO P POSITION WHEN PARKED." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "PARKING BRAKE OVERHEAT." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "PARKING BRAKE INOPERABLE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "CHECK PARKING BRAKE SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Electric parking brake system | ||
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| "CHECK POWER STEERING SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Power steering system | ||
| Power steering ECU assembly (for LHD) | ||
| Power steering ECU assembly (for RHD) | ||
| Combination meter assembly | ||
| "SHIFT TO P POSITION." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "KEY NOT DETECTED." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "TURN POWER OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "KEY DETECTED IN VEHICLE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| DEPRESS CLUTCH PEDAL, TOUCH ENGINE SWITCH WITH KEY." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "DEPRESS CLUTCH PEDAL AND PUSH ENGINE SWITCH TO START." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "SHIFT TO P POSITION TO START." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "KEY BATTERY LOW." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "AUTO POWER OFF TO CONSERVE BATTERY." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "SHIFT TO P POSITION AND PUSH ENGINE SWITCH TO TURN POWER OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "CHECK STEERING LOCK SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Steering lock system | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "STEERING LOCK ACTIVE." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Steering lock system | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "CHECK CLUTCH SWITCH." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. (w/ Entry and Start System) | CAN communication system | |
| Entry and start system (for Entry Function) | ||
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| "HEADLIGHT SYSTEM MALFUNCTION. VISIT YOUR DEALER." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Lighting system | ||
| Automatic high beam system (w/ Automatic High Beam System) | ||
| Headlight leveling ECU assembly (for LHD, w/o AFS) | ||
| Headlight leveling ECU assembly (for RHD, w/o AFS) | ||
| Headlight swivel ECU assembly (w/ AFS) | ||
| Combination meter assembly | ||
| "EFFECTIVENESS IS REDUCED DUE TO FAILURE, PLEASE STOP IN A SAFE AREA AND CHECK MANUAL." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Vehicle stability control system | ||
| Brake actuator assembly (skid control ECU) | ||
| Combination meter assembly | ||
| "TRC OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Vehicle stability control system | ||
| Brake actuator assembly (skid control ECU) | ||
| Combination meter assembly | ||
| "CHECK CHARGING SYSTEM." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "ENGINE OIL PRESSURE LOW." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| ECD system (for 1WW) | ||
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| "TURN LIGHTS OFF." message is displayed when it should not be, not displayed when it should be, or not displayed correctly. | CAN communication system | |
| Lighting system | ||
| Main body ECU (instrument panel junction block assembly) | - | |
| Combination meter assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| All buzzers do not operate normally. | Combination meter assembly | |
| Parking brake IOA hard warning buzzer does not operate | Electric parking brake system | |
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| Parking brake IOA soft warning buzzer does not operate | Electric parking brake system | |
| Parking brake with bracket actuator assembly | ||
| Combination meter assembly | ||
| Entry and start system warning buzzer does not operate (w/ Entry and Start System) | Entry and start system (for Entry Function) | |
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| Door open while not in P warning buzzer does not operate (w/ Entry and Start System) | Entry and start system (for Entry Function) | |
| Entry and start system (for Start Function) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| Immobiliser certification buzzer does not operate (w/ Engine Immobiliser System) | Engine Immobiliser System (w/ Entry and Start System) | |
| Engine Immobiliser System (w/o Entry and Start System) | ||
| Certification ECU (smart key ECU assembly) | Refer to Service Bulletin | |
| Combination meter assembly | ||
| Seat belt warning buzzer does not operate (Seat belt warning light operates normally) | Check customize setting | |
| Combination meter assembly | ||
| Key reminder buzzer does not operate (w/o Entry and Start System) | Key reminder warning system | |
| Speed limiter buzzer does not operate (w/ Speed Limiter System) | Speed limiter system | |
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| Brake fluid low warning buzzer does not operate | Brake master cylinder reservoir assembly (brake fluid level warning switch) | |
| Harness or connector | - | |
| Combination meter assembly | ||
| PKB-ON driving warning buzzer does not operate (Speedometer and parking brake warning light are operate normally) | Combination meter assembly | |
| Engine oil pressure warning buzzer does not operate | ECD system (for 1WW) | |
| ECD system (for 2WW) | ||
| ECM (for 1WW) | ||
| ECM (for 2WW) | ||
| Combination meter assembly | ||
| Driving with door ajar warning buzzer does not operate (Open door warning is operate normally) | Combination meter assembly | |
| Road sign assist buzzer does not operate (w/ Road Sign Assist System) | Road sign assist system | |
| Pre-crash safety city sensor | ||
| Combination meter assembly | ||
| EPS warning buzzer does not operate (EPS warning light is operate normally) | Combination meter assembly | |
| Engine coolant temperature warning buzzer does not operate (Engine coolant temperature gauge is operate normally) | Combination meter assembly | |
| Multi-information display warning buzzer does not operate | Combination meter assembly | |
| Light reminder warning buzzer does not operate (Open door warning and taillight indicator light operate normally) | Combination meter assembly | |
| Turn signal flasher buzzer does not operate (Turn indicator light normally) | Combination meter assembly | |
| Stop and start warning buzzer does not operate | Stop and start system | |
| Engine stop and start ECU | ||
| Combination meter assembly |