INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B0084SX

Click here

PROCEDURE


  1. PRECAUTION

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

    Click here

  3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  4. REMOVE HORN BUTTON ASSEMBLY

    Click here

  5. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  6. REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  7. REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

    Click here

  8. REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  9. REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  10. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

    Click here

  11. REMOVE TURN SIGNAL SWITCH

    Click here

  12. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  13. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  14. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

    Click here

  15. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip LH.

  16. REMOVE FRONT PILLAR GARNISH LH

    Click here

  17. REMOVE INSTRUMENT SIDE PANEL LH


    1. B0084D4C01
      B0087TV Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B0085OEC01
      B00847Z Remove in this Direction

      Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.

    3. B0083QNC01
      B00847Z Remove in this Direction

      Disengage the 3 guides to remove the instrument side panel LH as shown in the illustration.

  18. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. B008405C01

      Remove the 2 screws <C>.

    2. B0088NAC01
      B00847Z Remove in this Direction

      Disengage the 3 claws as shown in the illustration.

    3. B0088VLC01
      B00847Z Remove in this Direction

      Disengage the guide as shown in the illustration.

    4. Disconnect the connector.

    5. B0084O2

      Disengage the 2 claws to disconnect the DLC3 connector.

    6. Disengage the 2 clamps to remove the No. 1 instrument panel under cover sub-assembly.

  19. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. B0085NK

      Remove the 3 screws <C>.

    2. B0088SMC02
      B00847Z Remove in this Direction

      Disengage the 2 claws as shown in the illustration.

    3. Disconnect the connector.

    4. B0089I5

      Disengage the 2 claws to disconnect the DLC3 connector.

    5. Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.

  20. REMOVE NO. 2 METER HOOD CLUSTER


    1. B0087CIC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 3 clips to remove the No. 2 meter hood cluster as shown in the illustration.

  21. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B0085EI

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  22. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY


    1. B008790C01
      B00847Z Remove in this Direction

      Disengage the 6 clips as shown in the illustration.

    2. Disengage the clamp.

    3. Disconnect each connector to remove the No. 1 instrument panel sub-assembly.

  23. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    for LHD:

    Click here

    for RHD:

    Click here

  24. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. B0083F2

      Remove the 2 clips.

    2. B0085SYC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 2 clips as shown in the illustration.

    3. B0087PHC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 2 clips as shown in the illustration.

    4. B0083MYC01
      B00847Z Remove in this Direction

      Disengage the 2 guides as shown in the illustration.

    5. Disconnect the connector to remove the instrument cluster finish panel assembly.

  25. REMOVE COMBINATION METER ASSEMBLY

    Click here

  26. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B0088JUC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 5 clips to remove the lower instrument panel finish panel assembly as shown in the illustration.

    2. w/ Switch:


      1. Disconnect the connector.

  27. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Disengage the 8 clips in the order shown in the illustration.

      B00898FC01
      B0089GN Place Hand Here B00847Z Remove in this Direction

    2. Disengage the 3 clips in the order shown in the illustration.

      B0083YNC01
      B0089GN Place Hand Here B00847Z Remove in this Direction

    3. Disconnect the connector to remove the No. 3 instrument panel register assembly.

  28. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)

    Click here

  29. REMOVE INSTRUMENT CLUSTER FINISH PANEL COVER (w/o Radio Receiver)


    1. Disengage the 4 clips to remove the instrument cluster finish panel cover as shown in the illustration.

      B0088CFC01
      B0089GN Place Hand Here B00847Z Remove in this Direction

  30. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Radio Receiver)


    1. Disengage the 4 clips in the order shown in the illustration.

      B0088FLC01
      B0089GN Place Hand Here B00847Z Remove in this Direction

    2. Disengage the 5 clips as shown in the illustration.

      B0087X8C01
      B0089GN Place Hand Here B00847Z Remove in this Direction

    3. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  31. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. B004JR7

      Remove the 4 bolts <B>.

    2. Disconnect the connector to remove the radio tuner opening cover with bracket.

  32. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  33. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  34. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  35. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  36. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  37. REMOVE INSTRUMENT SIDE PANEL RH


    1. B0087BZC01
      B0087TV Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B0083MAC01
      B00847Z Remove in this Direction

      Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.

    3. B0087B3C01
      B00847Z Remove in this Direction

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  38. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B008537C01
      B00847Z Remove in this Direction

      Disengage the 4 claws as shown in the illustration.

    2. B00875CC01
      B00847Z Remove in this Direction

      Disengage the 2 guides as shown in the illustration.

    3. Disengage the clamp.

    4. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.

  39. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

    Click here

  40. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Passenger Side Knee Airbag)


    1. B00859LC01
      *a Screws <C>
      *b Bolts <D>

      Remove the 3 screws <C>.

    2. Remove the 2 bolts <D>.

    3. B0086QYC01
      B00847Z Remove in this Direction

      Disengage the 4 claws as shown in the illustration.

    4. Disconnect the connector to remove the lower instrument panel sub-assembly.

  41. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/ Passenger Side Knee Airbag)


    1. B0086SO

      Remove the 5 screws <C>.

    2. B0086P3C01
      B00847Z Remove in this Direction

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect the connector to remove the lower instrument panel sub-assembly.

  42. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL


    1. B0088R0C01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 2 clips as shown in the illustration.

    2. B008410C01
      B00847Z Remove in this Direction

      Disengage the 2 guides to remove the No. 1 instrument panel speaker panel as shown in the illustration.

  43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  44. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL


    1. B0084R4C01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 2 clips as shown in the illustration.

    2. B0087C9C01
      B00847Z Remove in this Direction

      Disengage the 2 guides to remove the No. 2 instrument panel speaker panel as shown in the illustration.

  45. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  46. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. B0084Z3C01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 4 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.

  47. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B0083KVC01
      B0089GN Place Hand Here
      B00847Z Remove in this Direction

      Disengage the 2 clips and 2 claws to remove the No. 1 instrument panel register assembly as shown in the illustration.

  48. DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)

    Click here

  49. DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)

    Click here

  50. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. B0086LUC01
      B00847Z Remove in this Direction

      Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor as shown in the illustration.

    2. Disconnect each connector.

      B00898YC01
      *A w/ Digital Audio Broadcasting Antenna or Television Antenna *B w/ Ion Generator
      *C w/ Headup Display - -

    3. Disengage each clamp.

    4. Remove the 2 clips.

      B0087SIC04
      *a Bolt <A> *b Bolt <B>
      *c Clip *d Nut <F>

    5. Remove the 4 bolts <B>, 2 bolts <A> and nut <F>.

    6. Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

      B0087LKC02
      B00847Z Remove in this Direction - -

      Note


      • Do not damage the instrument panel safety pad sub-assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.