АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В СБОРЕ СНЯТИЕ


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  2. REMOVE NO. 1 ENGINE UNDER COVER (for Pre-Runner)

  3. REMOVE NO. 2 ENGINE UNDER COVER (for Pre-Runner)

  4. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY (except Pre-Runner)


    1. A01E028E01

      Remove the 4 nuts, 4 bolts and frame crossmember.

  5. DISCONNECT CENTER EXHAUST PIPE ASSEMBLY


    1. Remove the 2 bolts and 2 nuts.

    2. Disconnect the center exhaust pipe from the front exhaust pipe and remove the gasket.

  6. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Выкрутите 2 болта и снимите 2 пружины сжатия.

    2. Отсоедините переднюю трубу от выпускной трубы и снимите прокладку.

    3. Снимите переднюю трубу с опоры.

  7. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  8. DRAIN AUTOMATIC TRANSMISSION FLUID


    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and the drain plug.

      Torque:
      20 N*m  { 205 kgf*cm, 15 ft.*lbf }

  9. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

    A01DZROE01

    1. Remove the transmission oil dipstick.

    2. Remove the 2 bolts and oil filler tube.

    3. Remove the O-ring from the oil filler tube.

  10. DISCONNECT OIL COOLER TUBE

    A01DV7AE02

    1. Using a union nut wrench, disconnect the oil cooler tube inlet and oil cooler tube outlet.

    2. A01DVMDE01

      Remove the 3 bolts and 3 clamps.

  11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    A01DZUZE01

    1. Remove the nut and disconnect the control cable.

    2. Remove the clip and disconnect the control cable.

  12. REMOVE STARTER ASSEMBLY

    Click here

  13. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

    A01E2VJE01

    1. Support the transmission with a transmission jack.

  14. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

    A01E24YE03

    1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

    2. Remove the 4 nuts, 4 bolts and frame crossmember.

  15. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

    A01E1RJ

    1. Remove the 4 bolts, ground cable and engine mounting insulator.

  16. DISCONNECT ENGINE WIRE

    A01E1UUE01

    1. Tilt the transmission downward.

      Note

      Make sure the cooling fan does not contact the fan shroud.

    2. Disconnect the connectors.

      A01DYZUE01
      Text in Illustration
      *A LH Side *B RH Side

      1. Disconnect the temperature sensor connector.

      2. Disconnect the park/neutral position switch connector.

      3. Disconnect the 3 speed sensor connectors.

      4. Disconnect the transmission wire connector.

  17. REMOVE WIRE HARNESS CLAMP BRACKET


    1. Remove the bolt and wire harness clamp bracket from the transmission.

  18. REMOVE STIFFENER PLATE


    1. Remove the 4 bolts and stiffener plate RH (with clamp tube).

      A01DXSNE01
      Text in Illustration
      *A LH Side *B RH Side

    2. Remove the 4 bolts and stiffener plate LH.

    3. Remove the No. 4 cylinder block insulator.

    4. Remove the No. 2 end plate.

  19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

    A01DZ6WE01

    1. Turn the crankshaft to gain access to each bolt.

    2. Hold the crankshaft pulley bolt with a wrench, and remove the 6 torque converter clutch mounting bolts.

    3. A01DX1IE01

      Remove the 5 bolts.

    4. Disconnect the transmission from the engine.

  20. REMOVE TRANSMISSION CONTROL CABLE BRACKET

    A01E13FE01

    1. Remove the 2 bolts and control cable bracket from the transmission.

  21. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY