POWER SEAT SWITCH INSPECTION

PROCEDURE


  1. INSPECT FRONT POWER SEAT SWITCH (w/ Memory)


    1. A004TM1E06
      Text in Illustration
      *1 Rear Lifter Switch
      *2 Reclining Switch
      *3 Front Vertical Switch
      *4 Slide Switch
      *5

      Component without harness connected

      (Power Seat Switch)

      for LH Side:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 3 (RCLF) Front Below 1 Ω
      2 (RCLR) - 3 (RCLF) Off Below 1 Ω
      1 (E) - 2 (RCLR) 10 kΩ or higher
      1 (E) - 3 (RCLF)
      1 (E) - 2 (RCLR) Rear Below 1 Ω
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 9 (SLDF) Front Below 1 Ω
      6 (SLDR) - 9 (SLDF) Off Below 1 Ω
      1 (E) - 6 (SLDR) 10 kΩ or higher
      1 (E) - 9 (SLDF)
      1 (E) - 6 (SLDR) Rear Below 1 Ω
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 10 (FUP) Up Below 1 Ω
      5 (FDWN) - 10 (FUP) Off Below 1 Ω
      1 (E) - 5 (FDWN) 10 kΩ or higher
      1 (E) - 10 (FUP)
      1 (E) - 5 (FDWN) Down Below 1 Ω
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 7 (RUP) Up Below 1 Ω
      7 (RUP) - 8 (RDWN) Off Below 1 Ω
      1 (E) - 7 (RUP) 10 kΩ or higher
      1 (E) - 8 (RDWN)
      1 (E) - 8 (RDWN) Down Below 1 Ω

      If the result is not as specified, replace the front power seat switch.

    2. A004QCHE05
      Text in Illustration
      *1 Slide Switch
      *2 Front Vertical Switch
      *3 Reclining Switch
      *4 Rear Lifter Switch
      *5

      Component without harness connected

      (Power Seat Switch)

      for RH Side:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 3 (RCLF) Front Below 1 Ω
      2 (RCLR) - 3 (RCLF) Off Below 1 Ω
      1 (E) - 2 (RCLR) 10 kΩ or higher
      1 (E) - 3 (RCLF)
      1 (E) - 2 (RCLR) Rear Below 1 Ω
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 9 (SLDF) Front Below 1 Ω
      6 (SLDR) - 9 (SLDF) Off Below 1 Ω
      1 (E) - 6 (SLDR) 10 kΩ or higher
      1 (E) - 9 (SLDF)
      1 (E) - 6 (SLDR) Rear Below 1 Ω
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 5 (FUP) Up Below 1 Ω
      5 (FUP) - 10 (FDWN) Off Below 1 Ω
      1 (E) - 5 (FUP) 10 kΩ or higher
      1 (E) - 10 (FDWN)
      1 (E) - 10 (FDWN) Down Below 1 Ω
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      1 (E) - 8 (RUP) Up Below 1 Ω
      7 (RDWN) - 8 (RUP) Off Below 1 Ω
      1 (E) - 7 (RDWN) 10 kΩ or higher
      1 (E) - 8 (RUP)
      1 (E) - 7 (RDWN) Down Below 1 Ω

      If the result is not as specified, replace the front power seat switch.

  2. INSPECT FRONT POWER SEAT SWITCH (w/o Memory)


    1. A004TM1E07
      Text in Illustration
      *1 Rear Lifter Switch
      *2 Reclining Switch
      *3 Front Vertical Switch
      *4 Slide Switch
      *5

      Component without harness connected

      (Power Seat Switch)

      for LH Side:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 3 (RCLF) Front Below 1 Ω
      2 (RCLR) - 4 (E)
      3 (RCLF) - 4 (E) Off Below 1 Ω
      2 (RCLR) - 4 (E)
      1 (B) - 2 (RCLR) Rear Below 1 Ω
      3 (RCLF) - 4 (E)
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 9 (SLDF) Front Below 1 Ω
      4 (E) - 6 (SLDR)
      4 (E) - 6 (SLDR) Off Below 1 Ω
      4 (E) - 9 (SLDF)
      1 (B) - 6 (SLDR) Rear Below 1 Ω
      4 (E) - 9 (SLDF)
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 10 (FUP) Up Below 1 Ω
      4 (E) - 5 (FDWN)
      4 (E) - 5 (FDWN) Off Below 1 Ω
      4 (E) - 10 (FUP)
      1 (B) - 5 (FDWN) Down Below 1 Ω
      4 (E) - 10 (FUP)
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 7 (RUP) Up Below 1 Ω
      4 (E) - 8 (RDWN)
      4 (E) - 7 (RUP) Off Below 1 Ω
      4 (E) - 8 (RDWN)
      1 (B) - 8 (RDWN) Down Below 1 Ω
      7 (RUP) - 4 (E)

      If the result is not as specified, replace the front power seat switch.

    2. A004QCHE06
      Text in Illustration
      *1 Slide Switch
      *2 Front Vertical Switch
      *3 Reclining Switch
      *4 Rear Lifter Switch
      *5

      Component without harness connected

      (Power Seat Switch)

      for RH Side:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 3 (RCLF) Front Below 1 Ω
      2 (RCLR) - 4 (E)
      3 (RCLF) - 4 (E) Off Below 1 Ω
      2 (RCLR) - 4 (E)
      1 (B) - 2 (RCLR) Rear Below 1 Ω
      3 (RCLF) - 4 (E)
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 9 (SLDF) Front Below 1 Ω
      4 (E) - 6 (SLDR)
      4 (E) - 6 (SLDR) Off Below 1 Ω
      4 (E) - 9 (SLDF)
      1 (B) - 6 (SLDR) Rear Below 1 Ω
      4 (E) - 9 (SLDF)
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 5 (FUP) Up Below 1 Ω
      4 (E) - 10 (FDWN)
      4 (E) - 5 (FUP) Off Below 1 Ω
      4 (E) - 10 (FDWN)
      1 (B) - 10 (FDWN) Down Below 1 Ω
      4 (E) - 5 (FUP)
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      1 (B) - 8 (RUP) Up Below 1 Ω
      4 (E) - 7 (RDWN)
      4 (E) - 7 (RDWN) Off Below 1 Ω
      4 (E) - 8 (RUP)
      1 (B) - 7 (RDWN) Down Below 1 Ω
      4 (E) - 8 (RUP)

      If the result is not as specified, replace the front power seat switch.