PARKING BRAKE CABLE (for 4WD and Pre-Runner) INSTALLATION


  1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

    A01E2MCE02
    Text in Illustration
    *1 No. 3 Parking Brake Cable *2 No. 3 Clip

    1. Install the No. 3 parking brake cable with the 3 bolts and nut.

      Torque:
      for Bolt A, Nut C
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }
      for Bolt B
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Install the No. 3 clip.

    3. Connect the No. 3 parking brake cable to the parking brake shoe lever LH and backing plate LH.


      1. Connect the No. 3 parking brake cable to the backing plate with the 2 bolts.

        Torque:
        9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      2. Connect the No. 3 parking brake cable to the parking brake shoe lever Click here.

  2. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

    A01DY5OE02
    Text in Illustration
    *1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer

    1. Install the No. 2 parking brake cable with the 4 bolts.

      Torque:
      for Bolt A
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }
      for Bolt B
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Connect the No. 2 parking brake cable to the parking brake equalizer and apply MP grease to the connecting portion.

    3. Connect the No. 2 parking brake cable to the parking brake shoe lever RH and backing plate RH.


      1. Connect the No. 2 parking brake cable to the backing plate with the 2 bolts.

        Torque:
        9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      2. Connect the No. 2 parking brake cable to the parking brake shoe lever Click here.

        Tech Tips

        Use the same procedure described for the LH side.

  3. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

    A01E2TBE01
    Text in Illustration
    *1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
    *3 Parking Brake Equalizer *4 Cable Support Bracket

    1. Connect the No. 1 parking brake cable to the parking brake lever Click here.

    2. Install the No. 1 parking brake cable clamp to the No. 1 parking brake cable.

    3. Install the No. 1 parking brake cable with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    4. Connect the No. 1 parking brake cable to the parking brake equalizer.

    5. Connect the No. 1 parking brake cable to the No. 3 parking brake cable and apply MP grease to the connecting portion.

    6. Install the pin and No. 1 clip.

    7. Attach the No. 1 parking brake cable to the cable support bracket.

    8. Install the No. 1 heat insulator with the 2 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  4. CHECK REAR BRAKE DRUM INSTALLATION


    1. Check that each part is installed properly.

      A01E13TE01
    2. A01E25P

      Measure the inside diameter of the drum and the diameter of the shoes. Check that the difference between the diameters is the correct shoe clearance.

      Standard shoe clearance
      0.6 mm (0.0236 in.)

      Note

      There should be no oil or grease on the contact surfaces of the shoe lining and drum.

  5. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY AND NEW GASKET

  6. INSTALL REAR WHEEL


    1. Install the wheel.

      Torque:
      105 N*m  { 1,070 kgf*cm, 77 ft.*lbf }

  7. ADJUST PARKING BRAKE

    Click here

  8. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.