CONDENSER(for 1WW) INSTALLATION

PROCEDURE

  1. INSTALL CONDENSER ASSEMBLY WITH RECEIVER

    1. E183345

      Install the condenser assembly with receiver as shown in the illustration.

      Tip:

      If the condenser is replaced with a new one, add compressor oil to the new condenser.

      Capacity

      40 cc (1.4 fl. oz)

      for HFC-134a(R134a): Compressor oil

      ND-OIL 8 or equivalent

      for HFO-1234yf(R1234yf): Compressor oil

      ND-OIL 12 or equivalent

  2. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY RH

    1. Install the upper radiator support sub-assembly RH with the 2 bolts.

      7.0 N*m

      71 kgf*cm

      62 in.*lbf

    2. Attach the clamp.

  3. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY LH

    1. Install the upper radiator support sub-assembly LH with the 2 bolts.

      7.0 N*m

      71 kgf*cm

      62 in.*lbf

  4. INSTALL UPPER RADIATOR SUPPORT

    1. Install the 2 radiator support cushions.

    2. Install the 2 upper radiator supports with the 2 bolts.

      19 N*m

      194 kgf*cm

      14 ft.*lbf

  5. CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

    1. Remove the attached vinyl tape from the tube and connecting part of the cooler condenser assembly.

    2. for HFC-134a (R134a):

      Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

      Compressor oil

      ND-OIL 8 or equivalent

    3. for HFO-1234yf (R1234yf):

      Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

      Compressor oil

      ND-OIL 12 or equivalent

    4. Install the O-ring to the air conditioning tube and accessory assembly.

    5. Connect the air conditioning tube and accessory assembly to the cooler condenser assembly with the bolt.

      5.4 N*m

      55 kgf*cm

      48 in.*lbf

  6. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

    1. Remove the attached vinyl tape from the pipe and connecting part of the cooler condenser assembly.

    2. for HFC-134a (R134a):

      Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

      Compressor oil

      ND-OIL 8 or equivalent

    3. for HFO-1234yf (R1234yf):

      Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

      Compressor oil

      ND-OIL 12 or equivalent

    4. Install the O-ring to the discharge hose sub-assembly.

    5. Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

      5.4 N*m

      55 kgf*cm

      48 in.*lbf

  7. CHARGE REFRIGERANT

    1. for HFC-134a(R134a):

      (Click here)

    2. for HFO-1234yf(R1234yf):

      (Click here)

  8. INSTALL FRONT BUMPER COVER

    (Click here)

  9. WARM UP ENGINE

    1. for HFC-134a(R134a):

      (Click here)

    2. for HFO-1234yf(R1234yf):

      (Click here)

  10. CHECK FOR REFRIGERANT GAS LEAK

    1. for HFC-134a(R134a):

      (Click here)

    2. for HFO-1234yf(R1234yf):

      (Click here)