PANORAMIC VIEW MONITOR SYSTEM, Diagnostic DTC:C1681

DTC Code DTC Name
C1681 Front Camera Feedback Malfunction

DESCRIPTION

DTC C1681 is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1681 Front Camera Feedback Malfunction Front television camera power supply failure

  • Harness or connector

  • Front television camera assembly

  • Television camera controller

 Television camera controller

WIRING DIAGRAM

B0089INE06

CAUTION / NOTICE / HINT

Note


  • When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

    Click here

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

    Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the R124 television camera controller connector.

    2. Disconnect the B7 front television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R124-15 (BCB+) - B7-6 (BCB+) Always Below 1 Ω
      R124-13 (BCV+) - B7-3 (BCV+) Always Below 1 Ω
      R124-14 (BCV-) - B7-2 (BCV-) Always Below 1 Ω
      R124-27 (BGND) - B7-5 (BGND) Always Below 1 Ω
      R124-25 (SGND) - Body ground Always 10 kΩ or higher
      R124-15 (BCB+) or B7-6 (BCB+) - Body ground Always 10 kΩ or higher
      R124-13 (BCV+) or B7-3 (BCV+) - Body ground Always 10 kΩ or higher
      R124-14 (BCV-) or B7-2 (BCV-) - Body ground Always 10 kΩ or higher
      R124-27 (BGND) or B7-5 (BGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)


    1. Disconnect the R124 television camera controller connector.

    2. B0087QJC23
      *a

      Component without harness connected

      (Television Camera Controller)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      27 (BGND) - Body ground Always Below 1 Ω
      14 (BCV-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEVISION CAMERA CONTROLLER Click here

    OK

  3. CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)


    1. B0088UCC07
      *a

      Component with harness connected

      (Television Camera Controller)

      Remove the television camera controller with the connector still connected.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R124-27 (BGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      R124-15 (BCB+) - R124-27 (BGND) Engine switch on (ACC) 5.5 to 7.05 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEVISION CAMERA CONTROLLER Click here

    OK

  4. CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)


    1. Remove the television camera controller with the connector still connected.

    2. Using an oscilloscope, check the waveform of the front television camera assembly.

      Tech Tips

      A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.

      B0086AUC02
      *a

      Component with harness connected

      (Television Camera Controller)

      		 *b Waveform 1 (camera lens not covered, displaying an image)
      *c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
      *e Video Waveform - -

      Tech Tips


      • The video waveform changes according to the image sent by the front television camera assembly.

      • The video waveform is constantly output when the engine switch is on (ACC).

      Measurement Condition
      Item Content
      Terminal No. (Symbol) R124-13 (BCV+) - R124-27 (BGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition Engine switch on (IG), panoramic view monitor system operating
      OK
      Waveform is similar to that shown in the illustration.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TELEVISION CAMERA CONTROLLER Click here

    NG

    REPLACE FRONT TELEVISION CAMERA ASSEMBLY Click here