POWER BACK DOOR SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start* / Data List.

      • *: w/ Entry and Start System

    5. According to the display on the GTS, read the Data List.

      Body Electrical > Back Door > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Door Lock Status

      Back door condition signal

      Lock or Unlock

      Lock: Back door locked

      Unlock: Back door unlocked

      -

      Half Latch SW

      Latch switch signal

      ON or OFF

      ON: Back door lock motor open-latched

      OFF: Back door lock motor full-latched or half-latched

      -

      Closer Position SW

      Sector switch signal

      ON or OFF

      ON: Back door lock sector gear in center position

      OFF: Back door lock sector gear out of center position

      -

      Courtesy SW

      Back door courtesy switch signal

      ON or OFF

      ON: Back door open

      OFF: Back door closed

      -

      PBD Touch Sensor (Right)

      Power back door sensor assembly RH signal

      ON, OFF or Open

      ON: Power back door sensor assembly RH pressed

      OFF: Power back door sensor assembly RH not pressed

      Open: Power back door sensor assembly RH circuit open

      -

      PBD Touch Sensor (Left)

      Power back door sensor assembly LH signal

      ON, OFF or Open

      ON: Power back door sensor assembly LH pressed

      OFF: Power back door sensor assembly LH not pressed

      Open: Power back door sensor assembly LH circuit open

      -

      PBD Main SW

      Power back door main switch signal

      ON or OFF

      ON: Power back door main switch pushed

      OFF: Power back door main switch not pushed

      -

      PBD Close SW

      Door control switch assembly signal

      ON or OFF

      ON: Door control switch assembly pushed

      OFF: Door control switch assembly not pushed

      -

      IG SW

      Ignition switch signal

      ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      "OFF" is also displayed for this item when the ignition switch is ACC.

      PBD Position (3/4-Open)

      Load signal detected during back door closing operation (3/4 - Open)

      Caution or OK

      Caution: Load detected between back door 3/4 and fully open position during back door closing operation

      OK: No load detected between back door 3/4 and fully open position during back door closing operation

      -

      PBD Position (2/4-3/4)

      Load signal detected during back door closing operation (2/4 - 3/4)

      Caution or OK

      Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation

      OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation

      -

      PBD Position (1/4-2/4)

      Load signal detected during back door closing operation (1/4 - 2/4)

      Caution or OK

      Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation

      OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation

      -

      PBD Position (Close-1/4)

      Load signal detected during back door closing operation (Close - 1/4)

      Caution or OK

      Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation

      OK: No load detected between back door fully closed and 1/4 open position during back door closing operation

      -

      Closed Position Initialization

      Back door fully closed position memorized signal

      Not Initialized or Initialized

      Not Initialized: Back door fully closed position not memorized

      Initialized: Back door fully closed position memorized

      -

      PBD SW Operation

      Power back door switch operation

      ON or 0.8s

      Current customize setting displayed

      -

      PBD Buzz In Use

      Power back door warning buzzer operation condition signal

      ON or OFF

      Current customize setting displayed

      -

      PBD Assist Open Operation

      Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated.

      OFF or ON

      Current customize setting displayed

      -

      PBD Assist Close Operation

      Function that enables or disables the power back door assist close operation. When PBD Assist Close is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated.

      OFF or ON

      Current customize setting displayed

      -

      Door Unlock with 1 Motion.

      Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door.

      Back Door or ALL DOORS

      Current customize setting displayed

      -

      Wireless Power Back Door Open

      Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

      Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8

      Current customize setting displayed

      Opening operation differs depending on the country.

      Power Back Door Opening Adjust

      Function that can be used to set the power back door opening angle at 5 different positions.

      Min, Small, Middle, Large or Max

      Current customize setting displayed

      -

      #Codes

      The number of DTCs

      Min.: 0

      Max.: 255

      The number of DTCs

      -

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Back Door Open

      Back door lock

      Permit or Prohibit

      Permit: Back door unlocked

      Prohibit: Back door locked

      -

      Back Door Open SW

      Back door control switch signal

      ON or OFF

      ON: Back door control switch on

      OFF: Back door control switch off

      -

      Back Door Open Handle SW

      Back door opener switch assembly signal

      ON or OFF

      ON: Back door opener switch assembly on

      OFF: Back door opener switch assembly off

      -

      Body Electrical > Entry&Start > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Tr/B-Door Unlock SW

      Back door opener switch assembly signal

      ON or OFF

      ON: Back door opener switch assembly on

      OFF: Back door opener switch assembly off

      -

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Back Door / Active Test.

    5. According to the display on GTS perform the "Active Test".

      Body Electrical > Back Door > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Latch Release

      Latch release operation

      ON or OFF

      -

      PBD Open/Close

      Power back door motor operation

      Forward, Reverse or OFF

      -

      PBD Buzzer

      Power back door warning buzzer sound

      ON or OFF

      -