REAR VIEW MONITOR SYSTEM Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the radio receiver assembly.

WIRING DIAGRAM

B0057AUE01

CAUTION / NOTICE / HINT

Note

Vehicle enrolled in telematics system (w/ Telematics Transceiver for G-BOOK) or telematics system (w/o Telematics Transceiver for G-BOOK):

When replacing the radio receiver assembly, perform the vehicle contract setting.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the I122 radio receiver assembly connector.

    2. Disconnect the Y6 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I122-11 (CA+) - Y6-6 (CB+) Always Below 1 Ω
      I122-12 (V+) - Y6-3 (CV+) Always Below 1 Ω
      I122-24 (V-) - Y6-2 (CV-) Always Below 1 Ω
      I122-23 (CGND) - Y6-5 (CGND) Always Below 1 Ω
      I122-11 (CA+) or Y6-6 (CB+) - Body ground Always 10 kΩ or higher
      I122-12 (V+) or Y6-3 (CV+) - Body ground Always 10 kΩ or higher
      I122-24 (V-) or Y6-2 (CV-) - Body ground Always 10 kΩ or higher
      I122-23 (CGND) or Y6-5 (CGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK RADIO RECEIVER ASSEMBLY


    1. B005BEVC15
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Remove the radio receiver assembly with the connector still connected.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I122-23 (CGND) - Body ground Always Below 1 Ω
      I122-24 (V-) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I122-11 (CA+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  3. CHECK REAR TELEVISION CAMERA ASSEMBLY


    1. Remove the radio receiver assembly with the connector connected.

      B005AWQC10
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      		 *b Waveform 1
      *c Waveform 2 *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio receiver assembly with the connector connected.

      OK
      Waveform is as shown in the illustration.
      Item Content
      Terminal No. (Symbol) I122-12 (V+) - I122-23 (CGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      Waveform 1: Engine switch on (IG), shift lever in R, camera lens not covered, displaying an image

      Waveform 2: Engine switch on (IG), shift lever in R, camera lens covered, blacking out screen

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (GVIF CABLE)


    1. Replace the GVIF cable with a new or normally functioning one.

    2. Check if the same malfunction recurs when the rear view monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).
      Result
      Proceed to
      OK
      NG

    OK

    END (GVIF CABLE IS DEFECTIVE)

    NG

  5. CHECK MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a new or normally functioning one.

      Click here

    2. Check if the same malfunction recurs when the rear view monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).
      Result
      Proceed to
      OK
      NG

    OK

    END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here