REAR COMBINATION LIGHT ASSEMBLY(w/ Rear No. 2 Seat) ON-VEHICLE INSPECTION

PROCEDURE


  1. INSPECT REAR COMBINATION LIGHT ASSEMBLY LH (for Turn Signal Light LED Type)


    1. Disconnect the S31 rear combination light assembly LH connector.

    2. Disconnect the Z21 rear light assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S31-5 (TRN1) - Z21-4 (TRN4) Always Below 1 Ω
      S31-6 (TRN2) - Z21-5 (TRN3) Always Below 1 Ω
      S31-5 (TRN1) or Z21-4 (TRN4) - Body ground Always 10 kΩ or higher
      S31-6 (TRN2) or Z21-5 (TRN3) - Body ground Always 10 kΩ or higher

      If the result is not as specified, repair or replace the wire harness or connector.

    4. Reconnect the Z21 rear light assembly LH connector.

    5. Reconnect the S31 rear combination light assembly LH connector.

    6. B005LC0C04
      *a

      Component with harness connected

      (Rear Combination Light Assembly LH)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S31-5 (TRN1) - S31-3 (E)*1 Engine switch on (IG), left turn signal light blinking 11 to 14 V ←→ Below 1 V
      S31-6 (TRN2) - S31-3 (E)*2 Engine switch on (IG), left turn signal light blinking 11 to 14 V ←→ Below 1 V

      • *1: If the result is not as specified, there may be a malfunction in the turn signal light circuit of the rear combination light assembly LH. Inspect the rear combination light assembly LH.

      • *2: If the result is not as specified, there may be a malfunction in the turn signal light circuit of the rear light assembly LH. Inspect the rear light assembly LH.

  2. INSPECT REAR COMBINATION LIGHT ASSEMBLY RH (for Turn Signal Light LED Type)


    1. Disconnect the S33 rear combination light assembly RH connector.

    2. Disconnect the Z20 rear light assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S33-5 (TRN1) - Z20-4 (TRN4) Always Below 1 Ω
      S33-6 (TRN2) - Z20-5 (TRN3) Always Below 1 Ω
      S33-5 (TRN1) or Z20-4 (TRN4) - Body ground Always 10 kΩ or higher
      S33-6 (TRN2) or Z20-5 (TRN3) - Body ground Always 10 kΩ or higher

      If the result is not as specified, repair or replace the wire harness or connector.

    4. Reconnect the Z20 rear light assembly RH connector.

    5. Reconnect the S33 rear combination light assembly RH connector.

    6. B005LC0C05
      *a

      Component with harness connected

      (Rear Combination Light Assembly RH)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S33-5 (TRN1) - S33-3 (E)*1 Engine switch on (IG), right turn signal light blinking 11 to 14 V ←→ Below 1 V
      S33-6 (TRN2) - S33-3 (E)*2 Engine switch on (IG), right turn signal light blinking 11 to 14 V ←→ Below 1 V

      • *1: If the result is not as specified, there may be a malfunction in the turn signal light circuit of the rear combination light assembly RH. Inspect the rear combination light assembly RH.

      • *2: If the result is not as specified, there may be a malfunction in the turn signal light circuit of the rear light assembly RH. Inspect the rear light assembly RH.