ECD SYSTEM (for DPF), Diagnostic DTC:P0115, P0117, P0118

DTC Code DTC Name
P0115 Engine Coolant Temperature Circuit
P0117 Engine Coolant Temperature Circuit Low Input
P0118 Engine Coolant Temperature Circuit High Input

DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

Tech Tips

If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).

P0115
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).

  • Open or short in engine coolant temperature sensor circuit

  • Engine coolant temperature sensor

  • ECM
P0117
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).

  • Short in engine coolant temperature sensor circuit

  • Engine coolant temperature sensor

  • ECM
P0118
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).

  • Open in engine coolant temperature sensor circuit

  • Engine coolant temperature sensor

  • ECM
Related Data List
DTC No. Data List
P0115 Coolant Temp
P0117
P0118

Tech Tips


  • If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:


    • Misfire

    • Combustion noise

    • Black smoke

    • White smoke

    • Lack of power

  • When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    Reference
    Temperature Displayed Malfunction
    -40°C (-40°F) Open circuit
    140°C (284°F) or higher Short circuit

WIRING DIAGRAM

A01E0KHE03

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    4. Read the value.

      OK
      70 to 90°C (158 to 194°F) with warm engine
      Result
      Result Proceed to
      -40°C (-40°F) A
      140°C (284°F) or higher B
      70 to 90°C (158 to 194°F) C

      Tech Tips


      • If there is an open circuit, the tester indicates -40°C (-40°F).

      • If there is a short circuit, the tester indicates 140°C (284°F) or higher.


    B

    READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) Click here

    C

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)


    1. A01E20XE08
      Text in Illustration
      *1 Engine Coolant Temperature Sensor
      *2 ECM
      *a

      Front view of wire harness connector

      (to Engine Coolant Temperature Sensor)

      Disconnect the engine coolant temperature sensor connector.

    2. Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON and turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    6. Read the value.

      OK
      140°C (284°F) or higher

    7. Reconnect the engine coolant temperature sensor connector.


    OK

    CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR. Click here

    NG

    CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) Click here

  3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)


    1. Disconnect the engine coolant temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      W1-2 - E26-5 (THW) Always Below 1 Ω
      W1-1 - E27-14 (E2) Always Below 1 Ω

    4. Reconnect the engine coolant temperature sensor connector.

    5. Reconnect the ECM connector.


    OK

    CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

  4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)


    1. A01DV8JE24
      Text in Illustration
      *1 Engine Coolant Temperature Sensor
      *2 ECM

      Disconnect the engine coolant temperature sensor connector.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON and turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    5. Read the value.

      OK
      -40°C (-40°F)

    6. Reconnect the engine coolant temperature sensor connector.


    OK

    REPLACE ENGINE COOLANT TEMPERATURE SENSOR Click here

    NG

    CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) Click here

  5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)


    1. Disconnect the engine coolant temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      W1-2 or E26-5 (THW) - Body ground Always 10 kΩ or higher

    4. Reconnect the engine coolant temperature sensor connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.


    1. Replace the engine coolant temperature sensor Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. REPLACE ENGINE COOLANT TEMPERATURE SENSOR


    1. Replace the engine coolant temperature sensor Click here.


    NEXT

  11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch to ON for 1 second.

    4. Enter the following menus: Powertrain / Engine and ECT / DTC.

    5. Confirm that the DTC is not output again.


    NEXT

    END