AIRBAG SYSTEM, Diagnostic DTC:B1835/58,B1836/58,B1837/58 and B1838/58

DTC Code DTC Name
B1835/58 Short in Curtain Shield Squib LH Circuit
B1836/58 Open in Curtain Shield Squib LH Circuit
B1837/58 Short to GND in Curtain Shield Squib LH Circuit
B1838/58 Short to B+ in Curtain Shield Squib LH Circuit

DESCRIPTION

The curtain shield squib LH circuit consists of the airbag sensor assembly and curtain shield airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Test Mode / Check Mode

B1835/58

Short in Curtain Shield Squib LH Circuit

  • The airbag sensor assembly detects a line short in the curtain shield squib LH circuit during primary check.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield squib LH (Curtain shield airbag assembly LH)

  • Airbag sensor assembly

Applies to check mode

B1836/58

Open in Curtain Shield Squib LH Circuit

  • The airbag sensor assembly detects an open in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield squib LH (Curtain shield airbag assembly LH)

  • Airbag sensor assembly

Applies to check mode

B1837/58

Short to GND in Curtain Shield Squib LH Circuit

  • The airbag sensor assembly detects a short to ground in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield squib LH (Curtain shield airbag assembly LH)

  • Airbag sensor assembly

Applies to check mode

B1838/58

Short to B+ in Curtain Shield Squib LH Circuit

  • The airbag sensor assembly detects a short to B+ in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield squib LH (Curtain shield airbag assembly LH)

  • Airbag sensor assembly

Applies to check mode

WIRING DIAGRAM

C284697E96

CAUTION / NOTICE / HINT

Note:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereClick here

Tip:

  • Perform the simulation method by selecting check mode (Signal Check) using the GTS.

    Click here

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

    Click hereClick hereClick here

PROCEDURE

  1. CHECK CONNECTORS

    1. C304235C01

      *1

      Curtain Shield Airbag Assembly LH

      *2

      Airbag Sensor Assembly

      *3

      Floor Wire

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag sensor assembly.

      OK

      The connectors are properly connected.

      Tip:

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the curtain shield airbag assembly LH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not damaged.

      OK

      The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the floor wire are not deformed or damaged.

      OK

      The short springs are not deformed or damaged.

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH

    1. C304239C02

      *1

      Curtain Shield Airbag Assembly LH

      *2

      Airbag Sensor Assembly

      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly LH)

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect a tester to the curtain shield airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note:

      • Do not forcibly insert SST into the terminals of the connector when connecting it.

      • Insert SST straight into the terminals of the connector.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      OK

      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.

      Tip:

      Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Disconnect SST from connector C.

    09843-18061

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

    NG

  3. CHECK FLOOR WIRE

    1. C304240C02

      *1

      Curtain Shield Airbag Assembly LH

      *2

      Airbag Sensor Assembly

      *3

      Floor Wire

      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly LH)

      Disconnect the floor wire from the airbag sensor assembly.

    2. Check for a short to B+ in the circuit.

      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        K7-1 (ICL+) - Body ground

        Ignition switch ON

        Below 1 V

        K7-2 (ICL-) - Body ground

        Ignition switch ON

        Below 1 V

      4. Turn the ignition switch off.

      5. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check for an open in the circuit.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        K7-1 (ICL+) - K7-2 (ICL-)

        Always

        Below 1 Ω

    4. Check for a short to ground in the circuit.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        K7-1 (ICL+) - Body ground

        Always

        1 MΩ or higher

        K7-2 (ICL-) - Body ground

        Always

        1 MΩ or higher

    5. Check for a short in the circuit.

      1. Release the activation prevention mechanism built into connector B.

        Click hereClick here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        K7-1 (ICL+) - K7-2 (ICL-)

        Always

        1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC

    1. C304238C01

      *1

      Curtain Shield Airbag Assembly LH

      *2

      Airbag Sensor Assembly

      Connect the connectors to the curtain shield airbag assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON, and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      OK

      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.

      Tip:

      Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    Result

    Proceed to

    OK

    NG
    OK

    USE SIMULATION METHOD TO CHECK

    Click hereClick hereClick here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY

    Click here