SFI SYSTEM, Diagnostic DTC:P0215

DTC Code DTC Name
P0215 Engine Shutoff Solenoid

DESCRIPTION

This DTC is stored when a malfunction is detected in the ECM power supply circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0215

Engine Shutoff Solenoid

The ECM is not powered properly.

  • Fuses

  • Engine room relay block

  • Instrument panel junction block

  • Wire harness or connector

  • Relay

Does not come on

DTC stored

WIRING DIAGRAM

A330559E01

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)

    1. Remove the EFI MAIN relay from the No. 1 engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (EFI MAIN relay) - A35-28 (MREL)

      Always

      Below 1 Ω

      5 (EFI MAIN relay) - A35-5 (+B1)

      Always

      Below 1 Ω

      5 (EFI MAIN relay) - A35-1 (ACT1)

      Always

      Below 1 Ω

      5 (EFI MAIN relay) - A35-6 (ACT2)

      Always

      Below 1 Ω

      5 (EFI MAIN relay) - A35-18 (ACT3)

      Always

      Below 1 Ω

      5 (EFI MAIN relay) - A35-30 (ACT4)

      Always

      Below 1 Ω

      1 (EFI MAIN relay) or A35-28 (MREL) - Body ground and other terminals

      Always

      10 kΩ or higher

      5 (EFI MAIN relay) or A35-5 (+B1) - Body ground and other terminals

      Always

      10 kΩ or higher

      5 (EFI MAIN relay) or A35-1 (ACT1) - Body ground and other terminals

      Always

      10 kΩ or higher

      5 (EFI MAIN relay) or A35-6 (ACT2) - Body ground and other terminals

      Always

      10 kΩ or higher

      5 (EFI MAIN relay) or A35-18 (ACT3) - Body ground and other terminals

      Always

      10 kΩ or higher

      5 (EFI MAIN relay) or A35-30 (ACT4) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Result

    Proceed to

    OK (w/ Entry and Start System)

    A

    OK (w/o Entry and Start System)

    B

    NG

    C
    B

    CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  2. CHECK HARNESS AND CONNECTOR (IG2 RELAY - ECM)

    1. Remove the IG2 relay from the center relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      5 (IG2 relay) - A35-19 (IGON)

      Always

      Below 1 Ω

      5 (IG2 relay) or A35-19 (IGON) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    GO TO ECM POWER SOURCE CIRCUIT

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

    1. Disconnect the ignition switch assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E21-6 (IG2) - A35-19 (IGON)

      Always

      Below 1 Ω

      E21-6 (IG2) or A35-19 (IGON) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    GO TO ECM POWER SOURCE CIRCUIT

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR