FRAME WIRE REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE ENGINE ASSEMBLY WITH TRANSMISSION

    Click here

  3. REMOVE FUEL TANK ASSEMBLY

    Click here

  4. REMOVE FRONT NO. 6 FLOOR HEAT INSULATOR


    1. B008GAD

      Remove the 3 nuts and front No. 6 floor heat insulator.

  5. REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR


    1. B008GBV

      Remove the 2 bolts and front No. 4 floor heat insulator.

  6. REMOVE FRONT FLOOR COVER LH


    1. B008GEZ

      Disengage the 6 clips to remove the front floor cover LH.

  7. REMOVE REAR SEAT ASSEMBLY LH

    Click here

  8. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  9. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER

    Click here

  10. REMOVE REAR SEAT SUB FLOOR PANEL

    Click here

  11. REMOVE NO. 2 ROOM PARTITION COVER

    Click here

  12. REMOVE NO. 1 LUGGAGE COMPARTMENT LAMP ASSEMBLY

    Click here

  13. REMOVE FRONT UPPER LUGGAGE COMPARTMENT TRIM COVER

    Click here

  14. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

    Click here

  15. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH (for LH Side)

    Click here

  16. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  17. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  18. REMOVE NO. 4 HV BATTERY SHIELD PANEL

    Click here

  19. REMOVE FRAME WIRE

    CAUTION:

    Wear insulated gloves.


    1. B008GAH

      Remove the battery terminal connector cover.

    2. B008GFF

      Remove the nut and disconnect the frame wire from the fusible link block assembly.

    3. B008GAU

      Disengage the 5 clamps.

    4. B008GBR

      Remove the earth terminal from the upper hybrid battery cover sub-assembly.

    5. B008GCN

      Disengage the 2 clamps.

    6. Disconnect the 2 frame wire connectors from the hybrid battery terminal block.

      Note

      Insulate the disconnected connectors with insulating tape.

    7. B008GEB

      Remove the nut.

    8. Disengage the clamp and remove the wiring harness protector.

    9. B008GCH

      Disengage the 4 clamps.

    10. B008GHS

      Disengage the 3 claws and push the frame wire out from the floor panel.

    11. for LHD:


      1. Remove the connector cover assembly.

        Click here

      2. B008GFO

        Remove the nut.

      3. Disengage the clamp.

      4. B008GAI

        Remove the bolt and disconnect the 2 frame wire connectors from the inverter with converter assembly.

        Note


        • Do not allow any foreign matter or water to enter the inverter with converter assembly.

        • Do not touch the connector waterproof seal or terminals.

        • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

        • Insulate the disconnected terminals with insulating tape.

        • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

      5. Temporarily install the connector cover assembly.

        Click here

      6. B008GHT

        Disengage the clamp.

      7. Remove the nut.

      8. Disengage the 2 claws and disconnect the frame wire from the engine room relay block and junction block assembly.

      9. B008GG2

        Disengage the 2 clamps and remove the wiring harness protector from the frame wire.

      10. B008GB7

        Remove the 3 bolts.

      11. B008GFPN01

        Disengage the clamp (A).

      12. Remove the 5 nuts.

      13. Disengage the clamp (B).

    12. for RHD:


      1. Remove the connector cover assembly.

        Click here

      2. B008GET

        Disengage the clamp.

      3. B008GHM

        Disconnect the air conditioning harness connector from the inverter with converter assembly.

        Note


        • Do not allow any foreign matter or water to enter the inverter with converter assembly.

        • Do not touch the connector waterproof seal or terminals.

        • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

        • Insulate the disconnected terminals with insulating tape.

        • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

      4. B008GEP

        Disengage the clamp.

      5. Remove the nut.

      6. Disengage the 2 claws and disconnect the frame wire from the engine room relay block and junction block assembly.

      7. B008GHZ

        Disengage the clamp.

      8. Remove the bolt and disconnect the frame wire connector from the inverter with converter assembly.

        Note


        • Do not allow any foreign matter or water to enter the inverter with converter assembly.

        • Do not touch the connector waterproof seal or terminals.

        • Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

        • Insulate the disconnected terminals with insulating tape.

        • Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

      9. Temporarily install the connector cover assembly.

        Click here

      10. B008GG2

        Disengage the 2 clamps and remove the wiring harness protector from the frame wire.

      11. B008GBN

        Remove the 3 bolts.

    13. B008GGO

      Disengage the clamp.

    14. Remove the bolt.

    15. B008GDG

      Remove the 2 clamps and frame wire.

      Note

      The clamps are non-reusable parts.