OIL PUMP REMOVAL

PROCEDURE

1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

   Click hereClick hereClick here

2. INSTALL ENGINE TO ENGINE STAND

   Click hereClick hereClick here

3. REMOVE THROTTLE BODY ASSEMBLY

   Click here

4. REMOVE AIR TUBE

   Click here

5. REMOVE INTAKE MANIFOLD

   Click here

6. REMOVE WIRE HARNESS CLAMP BRACKET

   Click here

7. REMOVE FUEL TUBE SUB-ASSEMBLY

   Click here

8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

   Click here

9. REMOVE FUEL INJECTOR ASSEMBLY

   Click here

10. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

11. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

12. REMOVE MANIFOLD STAY

    Click here

13. REMOVE EXHAUST MANIFOLD

    Click here

14. REMOVE PCV HOSE

    Click here

15. DISCONNECT NO. 3 WATER BY-PASS HOSE

    Click here

16. REMOVE WATER BY-PASS HOSE

    Click here

17. DISCONNECT WATER INLET HOSE

    Click here

18. REMOVE WATER INLET

    Click here

19. REMOVE THERMOSTAT

    Click here

20. REMOVE IGNITION COIL ASSEMBLY

    Click here

21. REMOVE VACUUM PUMP ASSEMBLY

    Click here

22. REMOVE NO. 1 VACUUM PUMP BRACKET

    Click here

23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Click hereClick here

24. REMOVE CYLINDER HEAD COVER GASKET

    Click hereClick here

25. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click hereClick here

26. REMOVE CRANKSHAFT PULLEY

    Click here

27. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

    Click hereClick here

28. REMOVE OIL FILTER CAP ASSEMBLY

    Click here

29. REMOVE ENGINE MOUNTING BRACKET STUD BOLT

    Click hereClick here

30. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

    1. 

       Remove the 3 bolts and engine mounting bracket.

    2. 

       Remove the 4 bolts and oil filter bracket.

    3. 

       Remove the 2 O-rings.

    4. 

       *1	Seal Washer

       Remove the 19 bolts and seal washer.

    5. 

       *1	Protective Tape

       Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

       Note:

       Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and timing chain cover sub-assembly.

       Tip:

       Tape the screwdriver tip before use.

    6. 

       Remove the 3 O-rings.

    7. 

       Remove the 3 bolts and engine water pump assembly.

    8. 

       Remove the gasket.

31. REMOVE TIMING CHAIN COVER OIL SEAL

    1. 

       *1	Protective Tape
       *2	Wooden Block

       Place the timing chain cover on wooden blocks.

    2. Using a screwdriver, tap out the timing chain cover oil seal.

       Note:

       Do not damage the surface of the oil seal press fit hole.

       Tip:

       Tape the screwdriver tip before use.

32. REMOVE CHAIN TENSIONER SLIPPER

    Click hereClick here

33. REMOVE NO. 1 CHAIN VIBRATION DAMPER

    Click hereClick here

34. REMOVE CHAIN SUB-ASSEMBLY

    Click hereClick here

35. REMOVE CRANKSHAFT TIMING SPROCKET

    1. 

       Remove the crankshaft timing sprocket.

36. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

    1. 

       Temporarily install the crankshaft pulley and crankshaft pulley bolt.

    2. Using SST, hold the crankshaft. Then remove the drive shaft gear nut.

       for 86 mm (3.39 in.) Bolt Pitch Type:

       09213-58014

       91551-80840

       09330-00021

       for 64 mm (2.52 in.) Bolt Pitch Type:

       09213-54015

       09330-00021

       Tip:

       For the 64 mm (2.52 in.) bolt pitch type, the part number of the installationbolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).

    3. Remove SST, the crankshaft pulley bolt and the crankshaft pulley.

    4. 

       Remove the bolt, chain tensioner plate and chain damper spring.

    5. 

       *1	Oil Pump Drive Gear
       *2	Oil Pump Drive Shaft Gear
       *3	No. 2 Chain Sub-assembly

       Remove the oil pump drive gear, oil pump drive shaft gear and No. 2 chain sub-assembly.

37. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

    1. 

       Remove the 10 bolts and 2 nuts.

    2. 

       Insert the blade of a No. 2 oil pan seal cutter between the stiffening crankcase and No. 2 oil pan sub-assembly. Cut through the sealer and remove the No. 2 oil pan sub-assembly.

       Note:

       • Be careful not to damage the surface of the oil pan which contacts the stiffening crankcase.

       • Be careful not to damage the stiffening crankcase flange.

38. REMOVE OIL PUMP ASSEMBLY

    1. 

       Remove the 3 bolts and oil pump assembly.