ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
*1 |
BATTERY |
*2 |
BATTERY BRACKET REINFORCEMENT |
*3 |
BATTERY CLAMP SUB-ASSEMBLY |
*4 |
BATTERY TRAY |
*5 |
FRONT BATTERY BRACKET |
*6 |
NO. 1 ENGINE UNDER COVER |
*7 |
NO. 2 CYLINDER HEAD COVER |
*8 |
RADIATOR RESERVOIR ASSEMBLY |
*9 |
REAR ENGINE UNDER COVER LH |
*10 |
REAR ENGINE UNDER COVER RH |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for Manual Transaxle |
*B |
for CVT |
*1 |
AIR CLEANER CAP SUB-ASSEMBLY |
*2 |
AIR CLEANER CASE SUB-ASSEMBLY |
*3 |
CLUTCH HOSE |
*4 |
COMPRESSOR WITH PULLEY ASSEMBLY |
*5 |
ECM |
*6 |
GENERATOR ASSEMBLY |
*7 |
NO. 1 RADIATOR HOSE |
*8 |
NO. 2 RADIATOR HOSE |
*9 |
V-RIBBED BELT |
*10 |
ECM CONNECTOR |
*11 |
ADJUSTING BAR |
*12 |
TERMINAL CAP |
*13 |
AIR CLEANER FILTER ELEMENT |
*14 |
ACCUMULATOR TO FLEXIBLE HOSE TUBE |
*15 |
CLIP |
*16 |
BREATHER PLUG HOSE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
FUEL TUBE SUB-ASSEMBLY |
*2 |
HEATER WATER OUTLET HOSE |
*3 |
HEATER WATER INLET HOSE |
*4 |
ENGINE ROOM JUNCTION BLOCK CONNECTOR |
*5 |
STARTER WIRE |
*6 |
CONNECTOR TUBE HOSE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for 4WD/AWD |
- |
- |
*1 |
DRIVE SHAFT BEARING BRACKET |
*2 |
FRONT AXLE SHAFT NUT LH |
*3 |
FRONT DRIVE SHAFT ASSEMBLY LH |
*4 |
FRONT DRIVE SHAFT ASSEMBLY RH |
*5 |
FRONT DRIVE SHAFT HOLE SNAP RING |
*6 |
FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
*7 |
FRONT SPEED SENSOR LH |
*8 |
FRONT STABILIZER LINK ASSEMBLY LH |
*9 |
TIE ROD END SUB-ASSEMBLY LH |
*10 |
FRONT STABILIZER BAR |
*11 |
SNAP RING |
*12 |
COTTER PIN |
*a |
for Axle Hub Spline Diameter 26 mm (1.02 in.) |
*b |
for Axle Hub Spline Diameter 30 mm (1.18 in.) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
MP grease |
 |
Do not apply lubricants to the threads |
ILLUSTRATION
*A |
for 4WD/AWD |
- |
- |
*1 |
FRONT EXHAUST PIPE ASSEMBLY |
*2 |
HEATED OXYGEN SENSOR |
*3 |
PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
*4 |
CENTER NO. 2 SUPPORT BEARING WASHER |
*5 |
GASKET |
*6 |
COMPRESSION SPRING |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
* |
For use with SST |
● |
Non-reusable part |
|
Do not apply lubricants |
ILLUSTRATION
*A |
for CVT |
*B |
for Manual Transaxle |
*1 |
TRANSAXLE CONTROL CABLE ASSEMBLY |
*2 |
ENGINE WIRE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
for CVT |
*B |
for 2WD |
*1 |
COLUMN HOLE COVER SILENCER SHEET |
*2 |
ENGINE MOUNTING INSULATOR LH |
*3 |
ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
*4 |
FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT |
*5 |
FRONT SUSPENSION MEMBER REINFORCEMENT LH |
*6 |
FRONT SUSPENSION MEMBER REINFORCEMENT RH |
*7 |
NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
*8 |
FRONT CROSSMEMBER SUB-ASSEMBLY |
*9 |
FRONT ENGINE MOUNTING INSULATOR |
*10 |
WIRE HARNESS CLAMP BRACKET |
*11 |
FRONT SUSPENSION MEMBER BRACE REAR RH |
*12 |
FRONT SUSPENSION MEMBER BRACE REAR LH |
*13 |
RADIATOR RESERVOIR BRACKET |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*A |
for Manual Transaxle |
*B |
for RHD |
*1 |
ENGINE HANGER |
*2 |
NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
*3 |
REAR ENGINE MOUNTING INSULATOR |
*4 |
STEERING GEAR HEAT INSULATOR |
*5 |
FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
*6 |
REAR ENGINE MOUNTING BRACKET |
*7 |
CLAMP |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
for CVT |
*B |
for RHD |
*C |
for 4WD/AWD |
- |
- |
*1 |
ENGINE HANGER |
*2 |
NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
*3 |
REAR ENGINE MOUNTING INSULATOR |
*4 |
STEERING GEAR HEAT INSULATOR |
*5 |
FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
*6 |
CLIP |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
for Manual Transaxle |
*B |
for 4WD/AWD |
*1 |
CLUTCH COVER ASSEMBLY |
*2 |
CLUTCH DISC ASSEMBLY |
*3 |
CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
*4 |
CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
*5 |
FLYWHEEL HOUSING SIDE COVER |
*6 |
FLYWHEEL SUB-ASSEMBLY |
*7 |
MANUAL TRANSAXLE ASSEMBLY |
*8 |
STARTER ASSEMBLY |
*9 |
TRANSFER ASSEMBLY |
*10 |
BLEEDER TO ACCUMULATOR TUBE |
*11 |
CLUTCH TUBE BOOT |
*12 |
ENGINE MOUNTING BRACKET LH |
*13 |
FRONT ENGINE MOUNTING BRACKET |
*14 |
REAR ENGINE MOUNTING BRACKET |
*15 |
ACCUMULATOR TO FLEXIBLE HOSE TUBE |
*16 |
CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |
*T1 |
1st: 49 (500, 36) 2nd: Turn 90° |
- |
- |
ILLUSTRATION
*A |
for CVT |
*B |
for 4WD/AWD |
*1 |
CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY |
*2 |
DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
*3 |
DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
*4 |
FLYWHEEL HOUSING SIDE COVER |
*5 |
STARTER ASSEMBLY |
*6 |
TRANSFER ASSEMBLY |
*7 |
FRONT DRIVE PLATE SPACER |
*8 |
REAR DRIVE PLATE SPACER |
*9 |
FLYWHEEL HOUSING UNDER COVER |
*10 |
REAR ENGINE MOUNTING BRACKET |
*11 |
ENGINE MOUNTING BRACKET LH |
*12 |
FRONT ENGINE MOUNTING BRACKET |
*a |
BLACK: x 1 SILVER: x 5 |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
★ |
Precoated part |