ROOF DRIP SIDE FINISH MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE

  1. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

    Note:

    When installing new No. 1 roof drip side finish moulding clips, remove any double-sided tape remaining where the No. 1 roof drip side finish moulding clips will be installed to the vehicle body and clean the vehicle body with a non-residue solvent.

    1. B370418C01

      *a

      Adhesive

      *b

      2 to 3 mm Bead of Adhesive

      Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new No. 1 roof drip side finish moulding clip.

      Tip:

      Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)

    2. for Normal Roof:

      1. Install the 2 No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 No. 1 roof drip side finish moulding clips after lightly applying adhesive.

        B378971C01

        *a

        Protruding Part

        -

        -

        Standard Measurement

        Area

        Measurement

        Area

        Measurement

        A

        11.2 mm (0.441 in.)

        B

        4.0 mm (0.157 in.)

        C

        1.1 mm (0.0433 in.)

        D

        3.6 mm (0.142 in.)

        E

        4.0 mm (0.157 in.)

        F

        16.9 mm (0.665 in.)

        G

        1.2 mm (0.0472 in.)

        H

        5.0 mm (0.197 in.)

    3. for Canvas Top:

      1. Install the 4 No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 4 No. 1 roof drip side finish moulding clips after lightly applying adhesive.

        B378970C01

        *a

        Protruding Part

        -

        -

        Standard Measurement

        Area

        Measurement

        Area

        Measurement

        A

        11.2 mm (0.441 in.)

        B

        4.0 mm (0.157 in.)

        C

        19.4 mm (0.764 in.)

        D

        1.5 mm (0.0591 in.)

        E

        3.6 mm (0.142 in.)

        F

        0.7 mm (0.0276 in.)

        G

        3.6 mm (0.142 in.)

        H

        4.0 mm (0.157 in.)

        I

        4.0 mm (0.157 in.)

        J

        4.8 mm (0.189 in.)

        K

        16.9 mm (0.665 in.)

        L

        8.1 mm (0.319 in.)

        M

        3.1 mm (0.122 in.)

        N

        11.1 mm (0.437 in.)

        O

        5.1 mm (0.201 in.)

        -

        -

    4. Install the roof drip side finish moulding when 20 minutes or more have elapsed after pressing and installing the No. 1 roof drip side finish moulding clips.

      Tip:

      • Initial hardening time: 20 minutes

      • Complete hardening time: 48 hours

  2. INSTALL ROOF DRIP SIDE FINISH MOULDING (for Normal Roof)

    1. B370417

      Engage the 2 No.1 roof drip side finish moulding clips to install the roof drip side finish moulding.

  3. INSTALL ROOF DRIP SIDE FINISH MOULDING (for Canvas Top)

    1. B370413

      Engage the 2 No.1 roof drip side finish moulding clips to install the roof drip side finish moulding.

  4. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING (for Canvas Top)

    1. B370415

      Engage the 2 No. 1 roof drip side finish moulding clips to install the rear roof drip side finish moulding.