CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) Short to GND in CAN Bus Line

DTC Code DTC Name
Short to GND in CAN Bus Line

DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Detection Item

Trouble Area

The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

  • Short between CAN bus lines and GND

  • ECM

  • Combination meter assembly

  • Power steering ECU assembly

  • Air conditioning amplifier assembly

  • Airbag sensor assembly

  • Spiral with sensor cable sub-assembly (steering angle sensor)

  • Radio and display receiver assembly*1

  • 4WD ECU assembly*2

  • Brake actuator assembly (skid control ECU)

  • Main body ECU (multiplex network body ECU)

  • Engine stop and start ECU*3

  • Telematics transceiver*4

  • No. 6 CAN junction connector

  • No. 7 CAN junction connector

  • DLC3 CAN branch wire or connector

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: for 4WD/AWD

*3: w/ Stop and Start System

*4: w/ Telematics Transceiver

WIRING DIAGRAM

C347971E02
C348129E02

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

  1. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)

    1. Disconnect the cable from the negative (-) battery terminal.

      C280369C32

      *a

      Front view of wire harness connector

      (to No. 6 CAN Junction Connector)

      *b

      Front view of DLC3

      *c

      to Main Body ECU (Multiplex Network Body ECU)

      *d

      to Power Steering ECU Assembly

      *e

      to Brake Actuator Assembly (Skid Control ECU)

      *f

      to No. 7 CAN Junction Connector

      *g

      to ECM

      *h

      to DLC3

      *i

      to Airbag Sensor Assembly

      *j

      to Air Conditioning Amplifier Assembly

    2. Disconnect the No. 6 CAN junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Connect to

      G171-1 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Main body ECU (multiplex network body ECU)

      G171-11 (CANL) - G14-4 (CG)

      G171-2 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Power steering ECU assembly

      G171-12 (CANL) - G14-4 (CG)

      G171-3 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Brake actuator assembly (skid control ECU)

      G171-13 (CANL) - G14-4 (CG)

      G171-4 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      No. 7 CAN junction connector

      G171-14 (CANL) - G14-4 (CG)

      G171-5 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      ECM

      G171-15 (CANL) - G14-4 (CG)

      G171-8 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      DLC3

      G171-18 (CANL) - G14-4 (CG)

      G171-9 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Airbag sensor assembly

      G171-19 (CANL) - G14-4 (CG)

      G171-10 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Air conditioning amplifier assembly

      G171-20 (CANL) - G14-4 (CG)

    Result

    Result

    Result

    Proceed to

    OK

    A

    NG (No. 7 CAN junction connector CAN main wire)

    B

    NG (DLC3 CAN branch wires)

    C

    NG (ECU or sensor CAN main or branch wires)

    D
    A

    REPLACE NO. 6 CAN JUNCTION CONNECTOR

    C

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    D

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)Click here

    B

  2. CONNECT CONNECTOR

    1. Reconnect the G171 No. 6 CAN junction connector.

    Result

    Proceed to

    NEXT
    NEXT

  3. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

    1. Disconnect the No. 7 CAN junction connector.

      C280369C54

      *a

      Front view of wire harness connector

      (to No. 7 CAN Junction Connector)

      *b

      Front view of DLC3

      *c

      to Combination Meter Assembly

      *d

      to Telematics Transceiver (w/ Telematics Transceiver)

      *e

      to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

      *f

      to Engine Stop and Start ECU (w/ Stop and Start System)

      *g

      to 4WD ECU Assembly (for 4WD/AWD)

      *h

      to No. 6 CAN Junction Connector

      *i

      to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)

      -

      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Connect to

      G172-1 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Combination meter assembly

      G172-11 (CANL) - G14-4 (CG)

      G172-2 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Telematics transceiver*4

      G172-12 (CANL) - G14-4 (CG)

      G172-3 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Radio and display receiver assembly*1

      G172-13 (CANL) - G14-4 (CG)

      G172-4 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Engine stop and start ECU*3

      G172-14 (CANL) - G14-4 (CG)

      G172-6 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      4WD ECU assembly*2

      G172-16 (CANL) - G14-4 (CG)

      G172-8 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      No. 6 CAN junction connector

      G172-18 (CANL) - G14-4 (CG)

      G172-9 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      Spiral with sensor cable sub-assembly (steering angle sensor)

      G172-19 (CANL) - G14-4 (CG)

      *1: w/ Audio and Visual System (for Radio and Display Type)

      *2: for 4WD/AWD

      *3: w/ Stop and Start System

      *4: w/ Telematics Transceiver

    Result

    Result

    Result

    Proceed to

    OK

    A

    NG (No. 6 CAN junction connector CAN main wire)

    B

    NG (ECU or sensor CAN main or branch wires)

    C
    A

    REPLACE NO. 7 CAN JUNCTION CONNECTOR

    B

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

    C

  4. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)

    1. C253362C03

      *a

      Front view of DLC3

      Reconnect the CAN junction connector.

    2. Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G14-6 (CANH) - G14-4 (CG)

      Cable disconnected from negative (-) battery terminal

      200 Ω or higher

      G14-14 (CANL) - G14-4 (CG)
      Tip:

      If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE CORRESPONDING ECU OR SENSOR

    NG

    REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR