ENTRY AND START SYSTEM(for Entry Function) OPERATION CHECK


  1. CHECK ENTRY AND START SYSTEM (for Entry Function) OPERATION

    Note

    Make sure that the entry and start system (for Entry Function) has not been canceled before performing this inspection.


    1. Check the entry unlock function (driver door, front passenger door, rear door LH, rear door RH).


      1. Perform a wireless lock operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.

      2. B008H99C01
        *A for LHD
        *B for RHD
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.

      3. With the system in unlock standby mode, grasp the front door outside handle assembly (for driver door) and check that the door unlocks.

        Tech Tips


        • The system is in unlock standby mode when the electrical key transmitter sub-assembly is in the detection area and the key ID code sent by the electrical key transmitter sub-assembly matches the key ID code stored by the certification ECU (smart key ECU assembly).

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door outside handle assembly.

        • Inspect the front passenger door, rear door LH and rear door RH using the same procedure.

      4. B008IPJC01
        *A for LHD
        *B for RHD
        *a Unlock Sensor (Backside)

        Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

        Note

        If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.

        Tech Tips

        Inspect the front passenger door, rear door LH and rear door RH using the same procedure.

    2. B008INZC01
      *A for LHD
      *B for RHD
      *a Lock Sensor

      Check the entry lock function (driver door, front passenger door, rear door LH, rear door RH).

      Note

      If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


      1. With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.

        Tech Tips


        • If the door does not lock even when touching the lock sensor, touch it with your palm.

        • Inspect the front passenger door, rear door LH and rear door RH using the same procedure.

      2. B008H99C01
        *A for LHD
        *B for RHD
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.7 to 1 m (2.30 to 3.28 ft.) below the bottom edge of the door glass and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door locks.

        Tech Tips


        • If the door does not lock even when touching the lock sensor, touch it with your palm.

        • As communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is carrying the electrical key transmitter sub-assembly, etc.

        • If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.

        • Inspect the front passenger door, rear door LH and rear door RH using the same procedure.

        • The door lock operation cannot be performed more than 3 times consecutively. (w/ Double Locking System)

    3. Check the entry back door open function.


      1. B008JMYC02
        *1 Back Door Opener Switch Assembly (Open Switch)
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Perform a wireless lock operation to lock the doors, operate the open switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly and check that the back door opens.

      2. Inspect the entry back door open operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the open switch of the back door opener switch assembly and check that the back door opens.

    4. Check the entry back door lock function.

      Note

      If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box or on the floor) and a back door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


      1. With the back door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door locks.

      2. B008GMVC02
        *1 Back Door Opener Switch Assembly (Lock Switch)
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the lock switch of the back door opener switch assembly and check that the back door locks.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper.

        • If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.

    5. Check the power back door close and lock function (w/ Power Back Door System).


      1. With the back door open, press the back door control switch while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door closes automatically and then locks.

        Tech Tips

        If the power back door control switch is pressed by a hand which is also holding the electrical key transmitter sub-assembly, the electrical key transmitter sub-assembly may not be detected as in the exterior detection area and the power back door close and lock function may not operate.

      2. B008GP9C03
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the power back door close and lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the back door control switch assembly twice and check that the back door closes automatically and then locks.

    6. Check hands free power back door operation (w/ Hands Free Power Back Door).


      1. Inspect the entry back door open operating range. Hold the electrical key transmitter sub-assembly at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration.

      2. With the back door closed, while carrying the electrical key transmitter sub-assembly, kick your leg so that your foot is 0.1 m (0.328 ft.) or closer to the rear bumper surface. Pull your leg away from the sensor and check that the back door begins to open automatically.

        B008H4IC02
        *1 Kick door control sensor - -
        *a Approximately 0.7 m (2.30 ft.) *b 0.1 m (0.328 ft.)

        Tech Tips


        • Refer to power back door system

          Click here

        • Inspect the close function using the same procedure.

    7. Check the push-button start function.


      1. With the engine switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly. Then, press the engine switch and check that the engine starts.

      2. With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.

        When the engine switch is pressed with the engine switch on (IG) and the shift lever not in P, the power source mode does not change to off, but changes to on (ACC).

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off).

        With the shift lever in P, check that the steering lock operates when a door is opened.

        When the engine switch is pressed after the vehicle is stopped, the engine stops and all the power turns off. However, if the shift lever is not in P when the engine switch is pressed with the vehicle stopped, the power source mode does not change to off, but changes to on (ACC).

      4. B008IPNC02
        *a Inspection Point

        Inspect the push-button start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note

        Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.

        • Perform the inspection for both inspection points.

      5. B008GS4C02
        *a Inspection Point

        Inspect the push-button start operating range (rear floor). Place the key on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note

        Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        Tech Tips


        • Communication may not be possible if the key is within 0.2 m (0.656 ft.) of the center of the rear seat cushion.

        • Perform the inspection for both inspection points.

      6. B008I80C04
        *a Inspection Point

        Inspect the push start operating range (luggage room). Place the electrical key transmitter sub-assembly on the luggage room floor at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note

        Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear corners of the luggage room.

        • Perform the inspection for both inspection points.

    8. Check the key lock-in prevention function (vehicle interior).

      Note

      In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.


      1. Turn the engine switch off.

      2. Place the electrical key transmitter sub-assembly on a front or rear seat.

      3. Close the door, making sure the doors are unlocked.

      4. Touch a door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.

    9. Check the transmitter battery saving function


      1. Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.

      2. Check that the entry and start system (for Entry Function) does not operate while in transmitter battery saving mode.

        Tech Tips

        To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.

    10. Check the entry cancel function.


      1. Cancel the entry and start system and check that all the functions of the entry and start system (for Entry Function) no longer operate.

        Click here

        Tech Tips

        While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.

    11. Check the answer-back function (hazard warning light flashing and buzzer* sounding).

      Entry Operation Hazard Warning Light Wireless Buzzer*
      Entry Lock Flashes once Sounds once
      Entry Unlock Flashes twice Sounds twice

      • *: w/ Wireless Door Lock Buzzer Answer-back Function

  2. KEY DIAGNOSTIC MODE (Using GTS)

    Tech Tips

    The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*6. For "Overhead + Rear Room"*6, the buzzer sounds in one long, continuous beep.

    Tech Tips


    • With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.

    • If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


    1. Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check (Key Diag Mode).


      Body Electrical > Entry&Start > Utility
      Tester Display
      Communication Check(Key Diag Mode)
    2. Inspect the appropriate item according to the following table.

      Tester Display Inspection Item
      [CH1/CH2] Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) (for Driver Door)
      [CH1] Overhead + Driver Side*1
      [CH2] Overhead + Driver Side*1
      [CH1/CH2] Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) (for Front Passenger Door)
      [CH1] Overhead + Passenger Side*2
      [CH2] Overhead + Passenger Side*2
      [CH1/CH2] Overhead + Driver Side Rear*3

      Rear door outside handle assembly LH (electrical key antenna) (for LHD)

      Rear door outside handle assembly RH (electrical key antenna) (for RHD)

      [CH1] Overhead +Driver Side Rear*3
      [CH2] Overhead + Driver Side Rear*3
      [CH1/CH2] Overhead + Passenger Side Rear*4

      Rear door outside handle assembly RH (electrical key antenna) (for LHD)

      Rear door outside handle assembly LH (electrical key antenna) (for RHD)

      [CH1] Overhead + Passenger Side Rear*4
      [CH2] Overhead + Passenger Side Rear*4
      [CH1/CH2] Overhead + Front Room*5 No. 1 indoor electrical key antenna assembly (front floor)
      [CH1] Overhead + Front Room*5
      [CH2] Overhead + Front Room*5
      [CH1/CH2] Overhead + Rear Room*6 No. 2 indoor electrical key antenna assembly (rear floor)
      [CH1] Overhead + Rear Room*6
      [CH2] Overhead + Rear Room*6
      [CH1/CH2] Overhead + Back Door*7 Electrical key antenna (outside luggage compartment)
      [CH1] Overhead + Back Door*7
      [CH2] Overhead + Back Door*7
      [CH1/CH2] Luggage + Back Door (inside)*8 No. 3 indoor electrical key antenna assembly (inside luggage)
      [CH1] Luggage + Back Door (inside)*8
      [CH2] Luggage + Back Door (inside)*8
      [CH1/CH2] Immobiliser Amp*9 Amplifier (engine switch)
      [CH1] Immobiliser Amp*9
      [CH2] Immobiliser Amp*9

      • [CH1]: Channel 1 is set.

      • [CH2]: Channel 2 is set.

      • [CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.

        *: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.

    3. Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless buzzer sounds.


      1. B008H99C01
        *A for LHD
        *B for RHD
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        *1: Front door outside handle assembly (for Driver door)

        Tech Tips


        • Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

        • *2, *3, *4: Perform the same inspection for the front passenger side, rear door LH side and rear door RH side.

    4. B008IPNC02
      *a Inspection Point

      *5: No. 1 indoor electrical key antenna assembly (front floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.

    5. B008GS4C02
      *a Inspection Point

      *6: No. 2 indoor electrical key antenna assembly (rear floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the rear seat cushion.

    6. B008H3JC01
      *a 0.7 to 1 m (2.30 to 3.28 ft.)

      *7: Electrical key antenna (outside luggage compartment)

      Tech Tips

      Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.

    7. B008I80C01
      *a Inspection Point

      *8: No. 3 indoor electrical key antenna assembly (inside luggage)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the luggage room floor.

    8. B008HOFC02
      *1 Engine Switch
      *2 Electrical Key Transmitter Sub-assembly

      *9: Amplifier (engine switch)

      Tech Tips

      While facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch.