SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P036500, P039000

DTC Code DTC Name
P036500 Camshaft Position Sensor "B" Bank 1 No Signal (sub)
P039000 Camshaft Position Sensor "B" Bank 2 No Signal (sub)

DESCRIPTION

Refer to DTC P036511.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P036500 Camshaft Position Sensor "B" Bank 1 No Signal (sub) No camshaft position sensor (for exhaust camshaft of bank 1) signal to the sub ECM while engine running ECM Comes on DTC stored SAE: P0365
P039000 Camshaft Position Sensor "B" Bank 2 No Signal (sub) No camshaft position sensor (for exhaust camshaft of bank 2) signal to the sub ECM while engine running ECM Comes on DTC stored SAE: P0390

MONITOR DESCRIPTION

While the engine is running, when the EV1 (EV2) signal is not input to the sub CPU even though the EV1 (EV2) signal is input to the main CPU, the ECM judges that a malfunction has occurred in an internal ECM circuit, and illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG).

  7. Turn the GTS on.

  8. Start the engine.

  9. Idle the engine for 10 seconds or more.

  10. Enter the following menus: Powertrain / Engine / Trouble Codes.

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  13. Input the DTC: P036500 or P039000.

  14. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

Tech Tips

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P036500 OR P039000)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P036500 or P039000 is output A
      DTC P036500 or P039000 and other DTCs are output B

      Tech Tips

      If any DTCs other than P036500 or P039000 are output, troubleshoot those DTCs first.


    A

    REPLACE ECM Click here

    B

    GO TO DTC CHART Click here