PARKING ASSIST MONITOR SYSTEM

CAUTION / NOTICE / HINT

PROCEDURE

1. VEHICLE BROUGHT TO WORKSHOP

   Result

   Proceed to
   NEXT

   NEXT

2. INSPECT BATTERY VOLTAGE

   1. Measure the battery voltage with the ignition switch off.

      Standard voltage

      11 to 14 V

      If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

   NEXT

3. CHECK IF SAME SYMPTOM APPEARS IN OTHER SYSTEM

   1. Refer to the navigation system.

      Click here

   Result

   Proceed to
   Navigation system is normal
   Navigation system is abnormal

   Navigation system is abnormal

   GO TO NAVIGATION SYSTEM

   Click here

   Navigation system is normal

4. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

   1. Use the GTS to check if the CAN communication system is functioning normally.

      for LHD (Click here)

      for RHD (Click here)

      Result

      Proceed to
      CAN DTCs are not output. (w/ Power Back Door System)
      CAN DTCs are not output. (w/o Power Back Door System)
      CAN DTCs are output. (for LHD)
      CAN DTCs are output. (for RHD)

   CAN DTCs are not output. (w/o Power Back Door System)

   CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)*Click here

   CAN DTCs are output. (for LHD)

   GO TO CAN COMMUNICATION SYSTEM (for LHD)

   Click here

   CAN DTCs are output. (for RHD)

   GO TO CAN COMMUNICATION SYSTEM (for RHD)

   Click here

   CAN DTCs are not output. (w/ Power Back Door System)

5. CHECK FOR DTC (BACK DOOR CLOSER SYSTEM)*

   1. Check for DTCs.

      Click here

   Result

   Proceed to
   Back door closer system DTCs are not output.
   Back door closer system DTCs are output.

   Back door closer system DTCs are output.

   GO TO BACK DOOR CLOSER SYSTEM

   Click here

   Back door closer system DTCs are not output.

6. CHECK FOR DTC (PARKING ASSIST MONITOR SYSTEM)*

   1. Check for DTCs and note any codes that are output.

      Click here

   2. Clear the DTCs.

      Click here

   3. Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

      Note:

      The navigation ECU sub-assembly outputs DTCs for the following systems. When DTCs other than those in Diagnostic Trouble Code Chart for the parking assist monitor system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

   Result

   Proceed to
   No DTCs are output.
   DTCs for parking assist monitor system are output.
   DTCs for navigation system are output.

   DTCs for parking assist monitor system are output.

   ADJUST, REPAIR OR REPLACEClick here

   DTCs for navigation system are output.

   GO TO NAVIGATION SYSTEM

   Click here

   No DTCs are output.

7. PERFORM SYMPTOMS TABLE

   1. Refer to the Problem Symptoms Table.

      Click here

   Result

   Proceed to
   Fault is not listed in Problem Symptoms Table
   Fault is listed in Problem Symptoms Table

   Fault is listed in Problem Symptoms Table

   ADJUST, REPAIR OR REPLACEClick here

   Fault is not listed in Problem Symptoms Table

8. OVERALL ANALYSIS AND TROUBLESHOOTING*

   1. Diagnosis System.

      Click here

   2. Terminals of ECU.

      Click here

   3. Data List / Active Test.

      Click here

   Result

   Proceed to
   NEXT

   NEXT

9. ADJUST, REPAIR OR REPLACE

   Result

   Proceed to
   NEXT

   NEXT

10. CONFIRMATION TEST

    Result

    Proceed to
    NEXT

    NEXT

    END