LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2786

DTC Code DTC Name
B2786 No Response from Steering Lock ECU

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2786

No Response from Steering Lock ECU

No communication between steering lock ECU (steering lock actuator assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more.

  • Steering lock ECU (steering lock actuator assembly)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

  • STRG LOCK fuse

WIRING DIAGRAM

B273275E33

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to Service Bulletin).

  • If the steering lock ECU (steering lock actuator assembly) is replaced, register the ECU code (refer to Service Bulletin).

PROCEDURE

  1. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Entry&Start > Trouble Codes

    Tip:

    When DTC B2786 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.

    Result

    Result

    Proceed to

    Only B2786 is output

    A

    DTC B2786 and B2785 are output simultaneously

    B
    B

    GO TO DTC B2785

    Click here

    A

  2. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - BATTERY AND BODY GROUND)

    1. Disconnect the E37 steering lock ECU (steering lock actuator assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E37-7 (B) - E37-1 (GND)

      Always

      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E37-1 (GND) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

    1. Disconnect the E35 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E35-17 (LIN) - E37-5 (LIN)

      Always

      Below 1 Ω

      E35-17 (LIN) - Body ground

      Always

      10 kΩ or higher

      E37-5 (LIN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

    1. Replace the steering lock ECU (steering lock actuator assembly).

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Entry&Start > Trouble Codes

      OK

      DTC B2786 is not output.

    Result

    Proceed to

    OK

    NG
    OK

    END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)