ROOF HEADLINING REASSEMBLY

PROCEDURE


  1. INSTALL NO. 1 ROOF WIRE (for Normal Roof)


    1. Apply butyl tape as shown in the illustration.

      B00844CC01
      *A w/ Room Light Assembly *B w/ Spot Light Assembly
      *a Marking - -
      B0087TV Butyl Tape - -

      Note

      Securely attach the butyl tape.

    2. Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

      B0084MPC01
      *A w/ Room Light Assembly *B w/ Spot Light Assembly
      *C w/ EC Mirror or Pre-collision System *D for LHD with Rain Sensor
      *a Marking Tape *b 90°
      *c Adjustment Area - -
      B00847Z Rotation Direction - -

    3. Engage each clamp.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    5. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    6. Install the No. 1 roof wire to the roof headlining with adhesive tape.

      B0088WPC01
      *A w/ Room Light Assembly *B w/ Spot Light Assembly
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 10 mm (0.394 in.) or more - -
      B0087TV Adhesive Tape - -
      Adhesive Tape Size
      Area Dimension Area Dimension
      A 20 mm (0.787 in.) B 80 mm (3.15 in.) or more

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  2. INSTALL NO. 1 ROOF WIRE (for Moon Roof)


    1. Apply butyl tape as shown in the illustration.

      B008502C01
      *a Marking - -
      B0087TV Butyl Tape - -

      Note

      Securely attach the butyl tape.

    2. Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

      B0084O4C01
      *a Marking Tape *b 90°
      *c Adjustment Area - -
      B00847Z Rotation Direction - -

    3. Engage the 5 clamps.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    5. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    6. Install the No. 1 roof wire to the roof headlining with adhesive tape.

      B008649C01
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 10 mm (0.394 in.) or more - -
      B0087TV Adhesive Tape - -
      Adhesive Tape Size
      Area Dimension Area Dimension
      A 20 mm (0.787 in.) B 80 mm (3.15 in.) or more

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  3. INSTALL NO. 1 ROOF WIRE (for Panoramic Moon Roof)


    1. Apply butyl tape as shown in the illustration.

      B008546C01
      *a Marking - -
      B0087TV Butyl Tape - -

      Note

      Securely attach the butyl tape.

    2. Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

      B00856PC01
      *A for LHD with Rain Sensor - -
      *a Marking Tape *b 90°
      *c Adjustment Area - -
      B00847Z Rotation Direction - -

    3. Engage each clamp.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    5. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    6. Install the No. 1 roof wire to the roof headlining with adhesive tape.

      B00840TC01
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 10 mm (0.394 in.) or more - -
      B0087TV Adhesive Tape - -
      Adhesive Tape Size
      Area Dimension Area Dimension
      A 20 mm (0.787 in.) B 80 mm (3.15 in.) or more

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  4. INSTALL VANITY LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side.


    1. B0088B6C01
      *1 Bulb Holder
      *a Claw (A)
      *b Claw (B)

      Engage the claw (B) to install the vanity light assembly.

    2. Engage the 2 claws (A) to install the bulb holder to the vanity light assembly.

  5. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  6. INSTALL NO. 4 ROOF SILENCER (for Normal Roof)


    1. Align the No. 4 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

      B0087LOC01
      *A w/ Room Light Assembly *B w/ Spot Light Assembly
      *a Hot-melt Glue *b Marking

  7. INSTALL NO. 2 ROOF SILENCER (for Normal Roof)


    1. Align the No. 2 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

      B008640C01
      *a Hot-melt Glue *b Marking