ROOF HEADLINING REMOVAL

PROCEDURE


  1. REMOVE DECK BOARD ASSEMBLY


    1. Remove the deck board assembly.

  2. REMOVE NO. 1 DECK BOARD


    1. Remove the No. 1 deck board.

  3. REMOVE NO. 2 DECK BOARD


    1. Remove the No. 2 deck board.

  4. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  5. REMOVE DECK FLOOR BOX RH


    1. B005XS1

      Disengage the 3 claws and remove the deck floor box RH.

  6. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  7. REMOVE BACK DOOR SCUFF PLATE


    1. B005XHV

      Disengage the 2 claws, 4 clips and 2 guides and remove the back door scuff plate.

  8. REMOVE SEAT TRACK BRACKET COVER RH

    Click here

  9. REMOVE REAR SEAT TRACK BRACKET COVER

    Click here

  10. REMOVE SEAT TRACK BRACKET COVER LH

    Click here

  11. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  12. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B005YWM

      Disengage the 10 claws and remove the front door scuff plate LH.

  13. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. B005XMB

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

  15. REMOVE FRONT PILLAR GARNISH LH


    1. B005Y4EE02
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      Tech Tips

      Let the front pillar garnish LH hang from the front pillar garnish clip.

    2. B005YF8

      While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

      Note


      • The front pillar garnish clip is reusable if it is not damaged.

      • If the front pillar garnish clip is damaged, replace it with a new one.

      Tech Tips

      When the front pillar garnish clip cannot be removed using your fingers:


      1. B005Y27

        While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow (1) shown in the illustration.

        Text in Illustration
        B005Z0W Lift in this Direction (1)
      2. B005YMS

        While pulling the front pillar garnish clip in the direction indicated by the arrow (2), push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.

        Text in Illustration
        B005Z0W Lift in this Direction (2)
    3. B005Y91E02

      Disengage the 2 guides (A).

    4. Disengage the guide (B) while pressing the shaded part in the illustration in the direction indicated by the arrow (2).

    5. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (3) in the illustration.

    6. B005Y09E02
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  16. REMOVE REAR DOOR SCUFF PLATE LH


    1. Move the rear seat assembly LH to the foremost position.

    2. B005YMZ

      Disengage the 9 claws and 3 clips, and remove the rear door scuff plate LH.

  17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

  18. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    Click here

  19. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  20. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. B005ZND

      Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.

  21. REMOVE CENTER PILLAR GARNISH LH


    1. B005XIH

      Remove the bolt.

    2. Disengage the 2 clips.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.

  22. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  23. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  25. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  27. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  28. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  30. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  31. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  32. REMOVE NO. 1 DECK TRIM COVER (for LH Side)


    1. B005YA2

      Using a moulding remover, disengage the 3 claws.

    2. Disengage the 2 guides and remove the No. 1 deck trim cover.

  33. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. B005ZL4

      Remove the 2 bolts.

    2. Disengage the 2 guides and remove the 2 luggage hold belt striker assemblies.

  34. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. B005YEL

      Using a moulding remover, disengage the 2 claws.

    2. Disengage the 2 guides and remove the front deck side trim cover LH.

  35. REMOVE NO. 2 CUP HOLDER


    1. B005Z29

      Disengage the 12 claws and remove the No. 2 cup holder.

  36. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

    Click here

  37. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Lower Side)

    Click here

  38. REMOVE NO. 2 ROOM LIGHT ASSEMBLY

    Click here

  39. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 bolts.

      B005Z5T

    2. Disengage the 7 claws, 5 clips and 5 guides, and remove the deck trim side panel assembly LH.

  40. REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Upper Side)

    Click here

  41. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. B005YXZ

      Using a moulding remover, disengage the 2 claws and 2 guides, and disconnect the belt guide LH.

    2. Pull the roof side inner garnish assembly LH in the direction indicated by the arrow (1) shown in the illustration to disengage the 7 clips (A).

      B005ZIDE03

    3. Pull the roof side inner garnish assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the 3 clips (B) and remove the roof side inner garnish assembly LH and rear roof side rail garnish as a unit.

  42. REMOVE REAR ROOF SIDE RAIL GARNISH LH


    1. B005XKI

      Disengage the 4 claws and guide, and remove the rear roof side rail garnish LH.

  43. REMOVE NO. 1 DECK TRIM COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  44. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  45. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  46. REMOVE NO. 1 CUP HOLDER


    1. B005YVI

      Disengage the 12 claws.

    2. Disconnect the connector and remove the No.1 cup holder.

  47. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  48. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Lower Side)

    Tech Tips

    Use the same procedure as for the LH side.

  49. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  50. REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Upper Side)

    Tech Tips

    Use the same procedure as for the LH side.

  51. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  52. REMOVE REAR ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  53. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

    Click here

  54. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  55. REMOVE NO. 2 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

    Click here

  56. REMOVE NO. 1 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

    Click here

  57. REMOVE MAP LIGHT ASSEMBLY (except Glass Roof)

    Click here

  58. REMOVE MAP LIGHT ASSEMBLY (for Glass Roof)

    Click here

  59. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  60. REMOVE SEAT BELT ANCHOR COVER


    1. B005XDP

      Using a moulding remover, disengage the 2 clips as shown in the illustration.

    2. Disengage the 2 claws and 2 guides, and remove the seat belt anchor cover.

  61. REMOVE FRONT ASSIST GRIP ASSEMBLY


    1. B005YLWE06
      Text in Illustration
      *1 Protective Tape
      *a Allow the covers to come off slightly

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. B005YJ9

      Disengage the 2 clips and remove the front assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other front assist grip assembly.

  62. REMOVE REAR ASSIST GRIP ASSEMBLY


    1. B005ZSPE04
      Text in Illustration
      *1 Protective Tape
      *a Allow the covers to come off slightly

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A005ERP

      Disengage the 2 clips and remove the rear assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other rear assist grip assembly.

  63. REMOVE VISOR ASSEMBLY LH


    1. B005Y7D

      Remove the 2 screws and visor assembly LH.

  64. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  65. REMOVE VISOR HOLDER


    1. B005XLIE04

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  66. DISCONNECT ROOF HEADLINING ASSEMBLY (except Glass Roof)


    1. w/ EC Mirror:


      1. Disconnect the connector.

    2. w/ Rain Sensor:


      1. Disconnect the connector.

    3. w/ Lane Departure Alert System:


      1. Disconnect the connector.

    4. Remove the protective cover from the front pillar.

      B005YEVE01
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    5. Disengage the 3 clamps and disconnect the connector from the front pillar LH.

    6. w/o Satellite Radio:


      1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

      2. Disengage the claw and disconnect the connector from the rear pillar RH.

    7. w/ Satellite Radio:


      1. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar RH.

      2. Disengage the claw and clamp, and disconnect the 2 connectors from the rear pillar RH.

    8. Install the protective cover to the front pillar.

    9. Remove the 5 clips and temporarily set down the roof headlining assembly in the cabin.

  67. DISCONNECT ROOF HEADLINING ASSEMBLY (for Glass Roof)


    1. w/ EC Mirror:


      1. Disconnect the connector.

    2. w/ Rain Sensor:


      1. Disconnect the connector.

    3. w/ Lane Departure Alert System:


      1. Disconnect the connector.

    4. Remove the protective cover from the front pillar.

      B005YGLE01
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    5. Disengage the 3 clamps and disconnect the connector from the front pillar LH.

    6. w/o Satellite Radio:


      1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

      2. Disengage the claw and disconnect the connector from the rear pillar RH.

    7. w/ Satellite Radio:


      1. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar RH.

      2. Disengage the claw and clamp, and disconnect the 2 connectors from the rear pillar RH.

    8. Install the protective cover to the front pillar.

    9. Remove the 3 clips.

    10. Disengage the 15 fasteners and temporarily set down the roof headlining assembly in the cabin.

      B005YIF

  68. REMOVE WINDSHIELD GLASS

    Click here

  69. REMOVE ROOF HEADLINING ASSEMBLY


    1. B005Z9A

      Remove the roof headlining assembly through the front of the vehicle.

      Note

      Do not damage the roof headlining assembly or body interior.