POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) Rear Power Window RH does not Operate with Rear Power Window Switch RH

DTC Code DTC Name
Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the ignition switch is ON, the rear power window regulator motor assembly RH is operated by the rear power window regulator switch assembly RH.

WIRING DIAGRAM

B341201E02

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

    1. Remove the rear power window regulator switch assembly RH.

      Click here

    2. Inspect the rear power window regulator switch assembly RH.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

    Click here

    OK

  2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    1. Remove the rear power window regulator motor assembly RH.

      Click here

    2. Inspect the rear power window regulator motor assembly RH.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)

    1. B276367C06

      *a

      Front view of wire harness connector

      (to Rear Power Window Regulator Switch Assembly RH)

      Disconnect the rear power window regulator switch assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      K1-3 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Ignition switch off

      Below 1 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)

    1. Disconnect K3 the rear power window regulator motor assembly RH connector.

    2. Disconnect K1 the rear power window regulator switch assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      K3-1 (U) - K1-4 (U)

      Always

      Below 1 Ω

      K3-2 (D) - K1-1 (D)

      Always

      Below 1 Ω

      K3-1 (U) or K1-4 (U) - Body ground

      Always

      10 kΩ or higher

      K3-2 (D) or K1-1 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

    1. Disconnect the K1 rear power window regulator switch assembly RH connector.

    2. Disconnect the J5*1 or I5*2 power window regulator master switch assembly connector.

      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 1. for LHD

      Tester Connection

      Condition

      Specified Condition

      K1-5 (SU) - J5-10 (U)

      Always

      Below 1 Ω

      K1-2 (SD) - J5-18 (D)

      Always

      Below 1 Ω

      K1-5 (SU) or J5-10 (U) - Body ground

      Always

      10 kΩ or higher

      K1-2 (SD) or J5-18 (D) - Body ground

      Always

      10 kΩ or higher
      Table 2. for RHD

      Tester Connection

      Condition

      Specified Condition

      K1-5 (SU) - I5-16 (U)

      Always

      Below 1 Ω

      K1-2 (SD) - I5-15 (D)

      Always

      Below 1 Ω

      K1-5 (SU) or I5-16 (U) - Body ground

      Always

      10 kΩ or higher

      K1-2 (SD) or I5-15 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR