FRONT LOWER SUSPENSION ARM(for RH Side) INSTALLATION

CAUTION / NOTICE / HINT

Tip:

For models with a 1WW or 1ND-TV engine, the front lower No. 1 suspension arm sub-assembly RH can be installed without removing the front suspension crossmember sub-assembly.

PROCEDURE

  1. TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (except 1WW, 1ND-TV)

    Click here

  2. TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for 1WW, 1ND-TV)

    1. Temporarily install the front lower No. 1 suspension arm sub-assembly RH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

      Note:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  3. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for 1WW, 1ND-TV)

    1. Connect the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.

      89 N*m

      908 kgf*cm

      66 ft.*lbf

      Note:

      Do not damage the boot of the ball joint.

  4. INSTALL FRONT WHEEL

    103 N*m

    1050 kgf*cm

    76 ft.*lbf

  5. STABILIZE SUSPENSION

    Click here

  6. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (except 8NR-FTS)

    1. C328247C02

      *a

      Torque Wrench Fulcrum Length
      V100136

      Turn

      Using SST, fully tighten the bolt (A).

      09961-01270

      Specified tightening torque

      233 N*m

      2376 kgf*cm

      172 ft.*lbf

      Note:

      This torque value is effective when SST is parallel to the torque wrench.

      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click hereClick here

      • When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 425 mm (1.39 ft.)):

        158 N*m (1611 kgf*cm, 117 ft.*lbf)

    2. Fully tighten the bolt (B).

      214 N*m

      2182 kgf*cm

      158 ft.*lbf

      Note:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  7. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for 8NR-FTS)

    1. C328096C01

      *a

      Ball joint Lock Nut Wrench

      *b

      Torque Wrench Fulcrum Length
      V100136

      Turn

      Using a ball joint lock nut wrench, fully tighten the bolt (A).

      Specified tightening torque

      233 N*m

      2376 kgf*cm

      172 ft.*lbf

      Note:

      This torque value is effective when ball joint lock nut wrench is parallel to the torque wrench.

      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click hereClick here

      • When using ball joint lock nut wrench (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 425 mm (1.39 ft.)):

        172.2 N*m (1756 kgf*cm, 127 ft.*lbf)

    2. Fully tighten the bolt (B).

      214 N*m

      2182 kgf*cm

      158 ft.*lbf

      Note:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  8. INSTALL NO. 1 ENGINE UNDER COVER (for Full Cover Type)

  9. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click hereClick here