TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 8 Sensor Type), Diagnostic DTC:C1AED

DTC Code DTC Name
C1AED Rear Sensor Communication Circuit

DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and ECU, or when there is a malfunction in a rear sensor.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AED

Rear Sensor Communication Circuit

An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the ignition switch is turned to ON.

  • Rear ultrasonic sensor circuit

  • Clearance warning ECU

WIRING DIAGRAM

E283768E16

PROCEDURE

  1. CHECK FOR DTC

    1. Clear the DTCs.

      Click here

    2. Recheck for DTCs.

      Click here

    Result

    Result

    Proceed to

    DTC C1AED is output

    A

    No DTC is output

    B
    B

    USE SIMULATION METHOD TO CHECK

    Click hereClick here

    A

  2. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 3 ULTRASONIC SENSOR [REAR CORNER SENSOR LH])

    1. Disconnect the G166 clearance warning ECU connector.

    2. Disconnect the S4 No. 3 ultrasonic sensor (rear corner sensor LH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G166-22 (BOR) - S4-1 (BI)

      Always

      Below 1 Ω

      G166-24 (SOR) - S4-3 (SI)

      Always

      Below 1 Ω

      G166-23 (E1) - S4-5 (EI)

      Always

      Below 1 Ω

      G166-22 (BOR) or S4-1 (BI) - Body ground

      Always

      10 kΩ or higher

      G166-24 (SOR) or S4-3 (SI) - Body ground

      Always

      10 kΩ or higher

      G166-23 (E1) or S4-5 (EI) - Body ground

      Always

      10 kΩ or higher

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (NO. 3 ULTRASONIC SENSOR [REAR CORNER SENSOR LH] - NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR LH])

    1. Disconnect the S4 No. 3 ultrasonic sensor (rear corner sensor LH) connector.

    2. Disconnect the S3 No. 4 ultrasonic sensor (rear center sensor LH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      S4-2 (BO) - S3-1 (BI)

      Always

      Below 1 Ω

      S4-4 (SO) - S3-3 (SI)

      Always

      Below 1 Ω

      S4-6 (EO) - S3-5 (EI)

      Always

      Below 1 Ω

      S4-2 (BO) or S3-1 (BI) - Body ground

      Always

      10 kΩ or higher

      S4-4 (SO) or S3-3 (SI) - Body ground

      Always

      10 kΩ or higher

      S4-6 (EO) or S3-5 (EI) - Body groung

      Always

      10 kΩ or higher

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR LH] - NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR RH])

    1. Disconnect the S3 No. 4 ultrasonic sensor (rear center sensor LH) connector.

    2. Disconnect the S2 No. 4 ultrasonic sensor (rear center sensor RH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      S3-2 (BO) - S2-1 (BI)

      Always

      Below 1 Ω

      S3-4 (SO) - S2-3 (SI)

      Always

      Below 1 Ω

      S3-6 (EO) - S2-5 (EI)

      Always

      Below 1 Ω

      S3-2 (BO) or S2-1 (BI) - Body ground

      Always

      10 kΩ or higher

      S3-4 (SO) or S2-3 (SI) - Body ground

      Always

      10 kΩ or higher

      S3-6 (EO) or S2-5 (EI) - Body ground

      Always

      10 kΩ or higher

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR RH] - NO. 3 ULTRASONIC SENSOR [REAR CORNER SENSOR RH])

    1. Disconnect the S2 No. 4 ultrasonic sensor (rear center sensor RH) connector.

    2. Disconnect the S1 No. 3 ultrasonic sensor (rear corner sensor RH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      S2-2 (BO) - S1-1 (BI)

      Always

      Below 1 Ω

      S2-4 (SO) - S1-3 (SI)

      Always

      Below 1 Ω

      S2-6 (EO) - S1-5 (EI)

      Always

      Below 1 Ω

      S2-2 (BO) or S1-1 (BI) - Body ground

      Always

      10 kΩ or higher

      S2-4 (SO) or S1-3 (SI) - Body ground

      Always

      10 kΩ or higher

      S2-6 (EO) or S1-5 (EI) - Body ground

      Always

      10 kΩ or higher

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

    1. Remove the No. 3 ultrasonic sensor (rear corner sensor RH).

      Click here

    2. Inspect the No. 3 ultrasonic sensor (rear corner sensor RH).

      Click here

    Result

    Result

    OK

    NG
    NG

    REPLACE NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

    Click here

    OK

  7. INSPECT NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

    1. Remove the No. 4 ultrasonic sensor (rear center sensor RH).

      Click here

    2. Inspect the No. 4 ultrasonic sensor (rear center sensor RH).

      Click here

    Result

    Result

    OK

    NG
    NG

    REPLACE NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

    Click here

    OK

  8. INSPECT NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

    1. Remove the No. 4 ultrasonic sensor (rear center sensor LH).

      Click here

    2. Inspect the No. 4 ultrasonic sensor (rear center sensor LH).

      Click here

    Result

    Result

    OK

    NG
    NG

    REPLACE NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

    Click here

    OK

  9. INSPECT NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

    1. Remove the No. 3 ultrasonic sensor (rear corner sensor LH).

      Click here

    2. Inspect the No. 3 ultrasonic sensor (rear corner sensor LH).

      Click here

    Result

    Result

    OK

    NG
    NG

    REPLACE NO. 3 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

    Click here

    OK

  10. REPLACE NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

    1. Replace the No. 3 ultrasonic sensor (rear corner sensor RH) with a normally functioning sensor.

      Click here

    Result

    Result

    NEXT
    NEXT

  11. CHECK FOR DTC (C1AED)

    1. Clear the DTCs.

      Click here

    2. Check for DTCs.

      Click here

    Result

    Result

    Proceed to

    DTC C1AED is output

    A

    No DTC is output

    B
    B

    END (NO. 3 ULTRASONIC SENSOR [REAR CORNER SENSOR RH] WAS DEFECTIVE)

    A

  12. REPLACE NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

    1. Replace the No. 4 ultrasonic sensor (rear center sensor RH) with a normally functioning sensor.

      Click here

    Result

    Result

    NEXT
    NEXT

  13. CHECK FOR DTC (C1AED)

    1. Clear the DTCs.

      Click here

    2. Check for DTCs.

      Click here

    Result

    Result

    Proceed to

    DTC C1AED is output

    A

    No DTC is output

    B
    B

    END (NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR RH] WAS DEFECTIVE)

    A

  14. REPLACE NO. 4 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

    1. Replace the No. 4 ultrasonic sensor (rear center sensor LH) with a normally functioning sensor.

      Click here

    Result

    Result

    NEXT
    NEXT

  15. CHECK FOR DTC (C1AED)

    1. Clear the DTCs.

      Click here

    2. Check for DTCs.

      Click here

    Result

    Result

    Proceed to

    DTC C1AED is output

    A

    No DTC is output

    B
    B

    END (NO. 4 ULTRASONIC SENSOR [REAR CENTER SENSOR LH] WAS DEFECTIVE)

    A

  16. REPLACE NO. 3 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

    1. Replace the No. 3 ultrasonic sensor (rear corner sensor LH) with a normally functioning sensor.

      Click here

    Result

    Result

    NEXT
    NEXT

  17. CHECK FOR DTC (C1AED)

    1. Clear the DTCs.

      Click here

    2. Check for DTCs.

      Click here

    Result

    Result

    Proceed to

    DTC C1AED is output (for LHD)

    A

    DTC C1AED is output (for RHD)

    B

    No DTC is output

    C
    A

    REPLACE CLEARANCE WARNING ECU ASSEMBLY

    Click here

    B

    REPLACE CLEARANCE WARNING ECU ASSEMBLY

    Click here

    C

    END (NO. 3 ULTRASONIC SENSOR [REAR CORNER SENSOR LH] WAS DEFECTIVE)