FRONT DRIVE SHAFT ASSEMBLY(for 1AD-FTV) DISASSEMBLY

PROCEDURE

  1. SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

    1. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    2. C239401

      Using needle-nose pliers, separate the front No. 2 axle inboard joint boot clamp.

  2. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

    1. C162722

      Using pliers, separate the front axle inboard joint boot clamp as shown in the illustration.

  3. SEPARATE FRONT AXLE INBOARD JOINT BOOT

    1. Separate the front axle inboard joint boot from the front drive inboard joint assembly.

  4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

    1. Remove the old grease from the front drive inboard joint assembly.

    2. F045461C03

      *a

      Matchmark

      Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

      Note:

      Do not use a punch for the marks.

    3. Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

    4. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    5. F045046

      Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.

    6. C141145C04

      *a

      Matchmark

      Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

      Note:

      Do not use a punch for the marks.

    7. Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

      Note:

      • Do not tap the rollers.

      • Do not drop the tripod joint.

  5. REMOVE FRONT AXLE INBOARD JOINT BOOT

    1. Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.

  6. REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)

    1. C197577

      Using pliers, remove the front drive shaft damper clamp.

    2. Remove the front drive shaft damper LH.

  7. SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

    1. C160725

      Using pliers, separate the front No. 2 axle outboard joint boot clamp.

  8. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

    Tip:

    Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.

  9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT

    1. Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

    2. Remove the old grease from the outboard joint.

  10. REMOVE FRONT DRIVE SHAFT DUST COVER LH

    1. F040647N02

      Using SST and a press, remove the front drive shaft dust cover LH.

      09950-00020

      Note:

      • Be careful not to drop the front drive inboard joint assembly.

      • Do not overtighten SST.

  11. REMOVE FRONT DRIVE SHAFT DUST COVER RH

    1. C067101

      Using a press, remove the front drive shaft dust cover RH.

      Note:

      Be careful not to drop the front drive inboard joint assembly.

  12. REMOVE DRIVE SHAFT BEARING CASE SNAP RING (for RH Side)

    1. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    2. C127662

      Using a screwdriver, separate the drive shaft bearing case snap ring from the drive shaft bearing case sub-assembly.

  13. REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY (for RH Side)

    1. C127663

      Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly.

      Note:

      Do not drop the front drive inboard joint assembly.

  14. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)

    1. C127664N01

      Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

      09950-00020

      Note:

      Do not drop the front drive inboard joint assembly.

  15. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

    1. C127665

      Using a snap ring expander, remove the snap ring.

    2. C127666N02

      Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly.

      09527-10011

    3. Remove the drive shaft bearing case snap ring.