ENGINE UNIT COMPONENTS
ILLUSTRATION
*1 |
NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
*2 |
NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
*3 |
NO. 2 RADIATOR HOSE |
*4 |
EXHAUST MANIFOLD TO HEAD GASKET |
*5 |
INLET EGR GASKET |
*6 |
EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY(TWC: Front Catalyst) |
*7 |
MANIFOLD STAY |
*8 |
FUEL DELIVERY PIPE |
*9 |
O-RING |
*10 |
FUEL INJECTOR ASSEMBLY |
*11 |
FUEL DELIVERY SPACER |
*12 |
GASKET |
*13 |
WATER HOSE |
*14 |
EGR VALVE ASSEMBLY |
*15 |
EGR VALVE GASKET |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
NO. 1 IGNITION COIL |
*2 |
OIL LEVEL DIPSTICK SUB-ASSEMBLY |
*3 |
V-RIBBED BELT TENSIONER ASSEMBLY |
*4 |
VENTILATION HOSE |
*5 |
NO.1 WATER BY-PASS PIPE |
*6 |
OIL LEVEL DIPSTICK GUIDE SUB-ASSEMBLY |
*7 |
O-RING |
*8 |
STUD BOLT |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
w/ Mesh Type |
*B |
w/o Mesh Type |
*1 |
CAMSHAFT POSITION SENSOR (for Exhaust Side) |
*2 |
OIL FILLER CAP SUB-ASSEMBLY |
*3 |
OIL FILLER CAP GASKET |
*4 |
VENTILATION VALVE SUB-ASSEMBLY |
*5 |
VENTILATION SYSTEM GROMMET |
*6 |
CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
*7 |
O-RING |
*8 |
SEAL WASHER |
*9 |
CYLINDER HEAD COVER SUB-ASSEMBLY |
*10 |
CYLINDER HEAD COVER GASKET |
*11 |
SPARK PLUG |
*12 |
CAMSHAFT BEARING CAP OIL HOLE GASKET |
*13 |
CAMSHAFT POSITION SENSOR (for Intake Side) |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Adhesive 1324 |
★ |
Precoated part |
ILLUSTRATION
*1 |
ENGINE MOUNTING BRACKET RH |
*2 |
ENGINE OIL PRESSURE SWITCH ASSEMBLY |
*3 |
KNOCK CONTROL SENSOR |
*4 |
ENGINE COOLANT TEMPERATURE SENSOR |
*5 |
TIMING CHAIN COVER SUB-ASSEMBLY |
*6 |
PLUG |
*7 |
GASKET |
*8 |
CRANK POSITION SENSOR |
*9 |
SEAL WASHER |
*10 |
O-RING |
*11 |
TIMING CHAIN COVER OIL SEAL |
*12 |
CRANKSHAFT PULLEY |
*13 |
WATER INLET |
*14 |
THERMOSTAT |
*15 |
SPRING |
*16 |
FRAME |
*17 |
NO. 2 WATER INLET HOUSING GASKET |
*18 |
ENGINE WATER PUMP ASSEMBLY |
*19 |
ELEMENT |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
★ |
Precoated part |
ILLUSTRATION
*A |
w/ Stop and Start System |
*B |
w/o Stop and Start system |
*C |
for No. 1 Chain Tensioner Assembly Installed with Nut |
*D |
for No. 1 Chain Tensioner Assembly Installed with Bolt |
*1 |
NO. 1 CHAIN TENSIONER ASSEMBLY |
*2 |
NO. 2 CHAIN VIBRATION DAMPER |
*3 |
GASKET |
*4 |
TIMING CHAIN GUIDE |
*5 |
TIMING CHAIN TENSION ARM |
*6 |
CHAIN SUB-ASSEMBLY |
*7 |
REAR ENGINE OIL SEAL |
*8 |
CRANKSHAFT BEARING |
*9 |
SNAP RING |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
Camshaft Bearing Cap Type A |
*B |
Camshaft Bearing Cap Type B |
*C |
Camshaft Bearing Cap Oil Hole Gasket without Mesh Type |
- |
- |
*1 |
CAMSHAFT BEARING CAP |
*2 |
CAMSHAFT |
*3 |
CAMSHAFT TIMING GEAR ASSEMBLY |
*4 |
CYLINDER HEAD SUB-ASSEMBLY |
*5 |
CYLINDER BLOCK WATER JACKET SPACER |
*6 |
CYLINDER HEAD GASKET |
*7 |
VALVE LASH ADJUSTER ASSEMBLY |
*8 |
NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
*9 |
CAMSHAFT HOUSING SUB-ASSEMBLY |
*10 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
*11 |
NO. 2 CAMSHAFT |
*12 |
PLATE WASHER |
*13 |
CYLINDER HEAD SET BOLT |
*14 |
RING PIN |
*15 |
OIL CONTROL VALVE FILTER |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
*T1 |
1st: 32 (326, 24) 2nd: turn 90° 3rd: turn 90° |
- |
- |
ILLUSTRATION
*1 |
CYLINDER BLOCK SUB-ASSEMBLY |
*2 |
NO. 1 OIL PAN BAFFLE PLATE |
*3 |
GASKET |
*4 |
OIL PAN DRAIN PLUG |
*5 |
O-RING |
*6 |
OIL FILTER DRAIN PLUG |
*7 |
OIL FILTER CAP |
*8 |
OIL FILTER ELEMENT |
*9 |
OIL PAN SUB-ASSEMBLY |
*10 |
OIL STRAINER SUB-ASSEMBLY |
*11 |
STRAIGHT PIN |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |