NAVIGATION SYSTEM Microphone Circuit between Microphone and Radio Receiver

DTC Code DTC Name
Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

  • w/o Manual (SOS) Switch

  • The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

    Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

  • w/ Manual (SOS) Switch

  • The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

    Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly via the telematics transceiver.

WIRING DIAGRAM

E268440E36

PROCEDURE

  1. CHECK MICROPHONE (OPERATION CHECK)

    1. E277821

      Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

      Click here

    2. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

      OK

      Check result is normal.

    Result

    Result

    Proceed to

    OK

    A

    NG

    (w/o Manual (SOS) Switch)

    B

    NG

    (w/ Manual (SOS) Switch)

    C
    A

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    for Sedan:Click here

    for Hatchback, Wagon:Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))Click here

    B

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

    1. Disconnect the E60 radio and display receiver assembly connector.

    2. Disconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-6 (SNS2) - O8-5 (SNS2)

      Always

      Below 1 Ω

      E60-4 (MACC) - O8-16 (MACC)

      Always

      Below 1 Ω

      E60-5 (MIN+) - O8-15 (MIC+)

      Always

      Below 1 Ω

      E60-19 (MIN-) - O8-14 (MIC-)

      Always

      Below 1 Ω

      E60-6 (SNS2) or O8-5 (SNS2) - Body ground

      Always

      10 kΩ or higher

      E60-4 (MACC) or O8-16 (MACC) - Body ground

      Always

      10 kΩ or higher

      E60-5 (MIN+) or O8-15 (MIC+) - Body ground

      Always

      10 kΩ or higher

      E60-19 (MIN-) or O8-14 (MIC-) - Body ground

      Always

      10 kΩ or higher

      E60-18 (SGND) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

    1. Reconnect the E60 radio and display receiver assembly connector.

    2. Reconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. E176671C24

      *a

      Component with harness connected

      (Radio and Display Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E60-4 (MACC) - Body ground

      Ignition switch ACC

      4 to 6 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-18 (SGND) - Body ground

      Always

      Below 1 Ω

      E60-19 (MIN-) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    for Sedan:Click here

    for Hatchback, Wagon:Click here

    OK

  4. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

    1. Remove the map light assembly (telephone microphone assembly).

      Click here

    2. E265420C01

      *a

      Component without harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      5 (SNS2) - 14 (MIC-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE TELEPHONE MICROPHONE ASSEMBLYClick here

    OK

  5. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

    1. Reconnect the E60 radio and display receiver assembly connector.

    2. Reconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. Turn the ignition switch to ACC.

    4. E234303C01

      *a

      Component with harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 15 (MIC+) and 14 (MIC-) of the O8 map light assembly (telephone microphone assembly) connector.

    5. Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

      Result

      Result

      Proceed to

      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output.

      A

      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output.

      B
    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    B

  6. REPLACE TELEPHONE MICROPHONE ASSEMBLY

    1. Replace the telephone microphone assembly with a new or known good one.

      Click here

    2. Check if the same malfunction recurs.

      Result

      Result

      Proceed to

      Malfunction does not recur (returns to normal).

      A

      Malfunction recurs.

      B
    A

    END

    B

    REPLACE MAP LIGHT ASSEMBLY

    Click here

  7. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

    1. Disconnect the E60 radio and display receiver assembly connector.

    2. Disconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-6 (SNS2) - O8-5 (SNS2)

      Always

      Below 1 Ω

      E60-6 (SNS2) or O8-5 (SNS2) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

    1. Disconnect the E143 telematics transceiver connector.

    2. Disconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E143-33 (MCVD) - O8-16 (MACC)

      Always

      Below 1 Ω

      E143-34 (MCI+) - O8-15 (MIC+)

      Always

      Below 1 Ω

      E143-35 (MCI-) - O8-14 (MIC-)

      Always

      Below 1 Ω

      E143-33 (MCVD) or O8-16 (MACC) - Body ground

      Always

      10 kΩ or higher

      E143-34 (MCI+) or O8-15 (MIC+) - Body ground

      Always

      10 kΩ or higher

      E143-35 (MCI-) or O8-14 (MIC-) - Body ground

      Always

      10 kΩ or higher

      E143-32 (SGND) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

    1. Disconnect the E60 radio and display receiver assembly connector.

    2. Disconnect the E143 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-5 (MIN+) - E143-18 (MCO+)

      Always

      Below 1 Ω

      E60-19 (MIN-) - E143-19 (MCO-)

      Always

      Below 1 Ω

      E60-5 (MIN+) or E143-18 (MCO+) - Body ground

      Always

      10 kΩ or higher

      E60-19 (MIN-) or E143-19 (MCO-) - Body ground

      Always

      10 kΩ or higher

      E60-18 (SGND) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

    1. Disconnect the E143 telematics transceiver connector.

    2. E289390C32

      *a

      Component with harness connected

      (Radio and Display Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-18 (SGND) - Body ground

      Always

      Below 1 Ω

      E60-19 (MIN-) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    Click here

    OK

  11. INSPECT TELEMATICS TRANSCEIVER

    1. Reconnect the E143 telematics transceiver connector.

    2. E259127C38

      *a

      Component with harness connected

      (Telematics Transceiver)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E143-33 (MCVD) - Body ground

      Ignition switch ACC

      4 to 6 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E143-32 (SGND) - Body ground

      Always

      Below 1 Ω

      E143-35 (MCI-) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE TELEMATICS TRANSCEIVER

    Click here

    OK

  12. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

    1. Remove the map light assembly (telephone microphone assembly).

      Click here

    2. E265420C01

      *a

      Component without harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      5 (SNS2) - 14 (MIC-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE TELEPHONE MICROPHONE ASSEMBLYClick here

    OK

  13. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

    1. Reconnect the E60 radio and display receiver assembly connector.

    2. Reconnect the O8 map light assembly (telephone microphone assembly) connector.

    3. Reconnect the E143 telematics transceiver connector.

    4. Turn the ignition switch to ACC.

    5. E234303C01

      *a

      Component with harness connected

      (Map Light Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 15 (MIC+) and 14 (MIC-) of the O8 map light assembly (telephone microphone assembly) connector.

    6. Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

      Result

      Result

      Proceed to

      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output.

      A

      A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output.

      B
    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    B

  14. REPLACE TELEPHONE MICROPHONE ASSEMBLY

    1. Replace the telephone microphone assembly.

      Click here

    2. Check if the same malfunction recurs.

      Result

      Result

      Proceed to

      Malfunction does not recur (returns to normal).

      A

      Malfunction recurs.

      B
    A

    END

    B

    REPLACE MAP LIGHT ASSEMBLY

    Click here