METER / GAUGE SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    • Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    • Some items displayed on the tester may not be applicable depending on the vehicle specifications.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body or Powertrain / (desired system) / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Table 1. Combination Meter

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      ODO/TRIP Change SW

      ODO/TRIP switch (meter) condition/ON or OFF

      ON: ODO/TRIP switch pushed

      OFF: ODO/TRIP switch not pushed

      -

      ODO/TRIP Change SW

      ODO/TRIP switch (steering pad switch) condition/ON or OFF

      ON: ODO/TRIP switch pushed

      OFF: ODO/TRIP switch not pushed

      -

      P-Seatbelt Buckle SW

      Front passenger side seat belt warning light request signal/ON or OFF

      ON: Tongue plate (for front passenger side) not inserted

      OFF: Tongue plate (for front passenger side) inserted

      -

      Water Level SW

      Water level switch condition/ON or OFF

      ON: Water level warning switch on

      OFF: Water level warning switch off

      for 1WW

      Vehicle Speed Meter

      Vehicle speed/Min.: 0 (0), Max.: 255 (158)

      Almost same as actual vehicle speed (when driving)

      Unit: km/h (mph)

      Engine Rpm

      Engine speed/Min.: 0, Max.: 12750

      Idling: 700 to 800

      Unit: rpm

      Coolant Temperature

      Engine coolant temperature/Min.: 0 (0), Max.: 127.5 (261.5)

      After warming up: 80 to 95 (176 to 203)

      • Unit: °C (°F).

      • If the value is 0 (0), the sensor circuit is open.

      • If the value is 127.5 (261.5), the sensor circuit is shorted.

      Multi Display Select Switch

      Steering pad switch/ON or OFF

      ON: Steering pad DISP switch on

      Off: Steering pad DISP switch off

      -

      +B Voltage Value

      +B voltage/Min.: 0, Max.: 25.5

      Between 1 and 14

      Unit: V

      Fuel Input

      Fuel sender gauge input/Min.: 0, Max.: 127.5

      Fuel sender gauge input value

      Unit: L

      Ambient Temperature

      Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)

      Almost the same as actual outside temperature

      The temperature displayed on the multi-information display is -40 to 87.5°C (-40 to 189.5°F)

      2nd-Row Seatbelt Buckle (R)

      Buckle switch (Rear No. 1 seat RH side)/ON or OFF

      ON: Tongue plate (for rear No. 1 seat RH side) not inserted

      OFF: Tongue plate (for rear No. 1 seat RH side) inserted

      w/ Rear No. 1 Seat

      2nd-Row Seatbelt Buckle (L)

      Buckle switch (Rear No. 1 seat LH side)/ON or OFF

      ON: Tongue plate (for rear No. 1 seat LH side) not inserted

      OFF: Tongue plate (for rear No. 1 seat LH side) inserted

      w/ Rear No. 1 Seat

      2nd-Row Seatbelt Buckle (C)2

      Buckle switch (Rear No. 1 seat center)/ON or OFF

      ON: Tongue plate (for rear No. 1 seat center) not inserted

      OFF: Tongue plate (for rear No. 1 seat center) inserted

      w/ Rear No. 1 Seat

      3rd-Row Seatbelt Buckle (R)

      Buckle switch (Rear No. 2 seat RH side)/ON or OFF

      ON: Tongue plate (for rear No. 2 seat RH side) not inserted

      OFF: Tongue plate (for rear No. 2 seat RH side) inserted

      w/ Rear No. 2 Seat

      3rd-Row Seatbelt Buckle (L)

      Buckle switch (Rear No. 2 seat LH side)/ON or OFF

      ON: Tongue plate (for rear No. 2 seat LH side) not inserted

      OFF: Tongue plate (for rear No. 2 seat LH side) inserted

      w/ Rear No. 2 Seat

      Oil Pressure Switch

      Oil pressure switch/ON or OFF

      ON: Oil pressure switch on

      OFF: Oil pressure switch off

      -

      Turn Signal Switch (Left)

      Turn signal switch (left) /ON or OFF

      ON: Turn signal switch (left) on

      OFF: Turn signal switch (left) off

      -

      Turn Signal Switch (Right)

      Turn signal switch (right) /ON or OFF

      ON: Turn signal switch (right) on

      OFF: Turn signal switch (right) off

      -

      Key Remind Sound

      Key reminder sound/Fast, Normal or Slow

      Current key reminder buzzer speed setting displayed

      w/o Entry and Start System

      Driver Side Seatbelt Warning Buzzer

      Driver side seat belt warning buzzer setting/ON or OFF

      ON: Driver side seat belt warning buzzer enabled

      OFF: Driver side seat belt warning buzzer disabled

      -

      P-Seatbelt Warning Buzzer

      Front passenger side seat belt warning buzzer setting/ON or OFF

      ON: Front passenger side seat belt warning buzzer enabled

      OFF: Front passenger side seat belt warning buzzer disabled

      -

      Rear Seatbelt Warning Buzzer

      Rear seat belt warning buzzer setting/ON or OFF

      ON: Rear seat belt warning buzzer enabled

      OFF: Rear seat belt warning buzzer disabled

      w/ Rear No. 1 Seat, w/ Rear No. 2 Seat

      ECO Drive Indicator Zone

      Eco driving indicator light signal/ON or OFF

      ON: Eco driving indicator light on

      OFF: Eco driving indicator light off

      for CVT

      ODO Display Time After IG OFF Setting

      Condition of the ODO display time/30 s, 60 s, 600 s or OFF

      Displays odometer display time setting

      -

      TPMS System*1

      Existence of function/With or Without

      With: w/ Tire Pressure Warning System

      Without: w/o Tire Pressure Warning System

      -

      LDA System

      Existence of function/With or Without

      With: w/ Lane Departure Alert System

      Without: w/o Lane Departure Alert System

      -

      PCS System

      Existence of function/With or Without

      With: w/ Pre-collision System

      Without: w/o Pre-collision System

      -

      Number of Trouble Code

      Number of DTCs currently stored

      0

      -
      Table 2. Engine (for ZR Series Engine)

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Engine Speed

      Engine speed/

      Min.: 0 rpm, Max.: 16383 rpm

      • 580 to 680 rpm: Idling (for Manual Transaxle)

      • 600 to 700 rpm: Idling (except Manual Transaxle)

      -

      Vehicle Speed

      Vehicle speed/

      Min.: 0 km/h, Max.: 255 km/h

      Actual vehicle speed

      The speed is indicated on the speedometer.
      Table 3. Engine (for 1WW)

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Engine Speed

      Engine speed/

      Min.: 0 rpm, Max.: 16383 rpm

      Min.: 0 rpm, Max.: 16383 rpm

      When the crankshaft position sensor is malfunctioning, "Engine speed" is approximately 0 or varies greatly from the actual engine speed.

      Vehicle Speed

      Vehicle speed/

      Min.: 0 km/h, Max.: 255 km/h

      Actual vehicle speed

      -

  2. ACTIVE TEST

    Tip:

    • Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    • Some items displayed on the tester may not be applicable depending on the vehicle specifications.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Combination Meter / Active Test.

    5. According to the display on the intelligent tester, perform the Active Test.

      Table 4. Combination Meter

      Tester Display

      Test Part

      Control Range

      Diagnostic Note

      Speed Meter Operation*1

      Speedometer

      0, 40, 80, 120, 160, 200 or 240

      Perform the test with the vehicle stopped and the engine idling.

      Tachometer Operation

      Tachometer

      0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000

      Perform the test with the vehicle stopped and the engine idling.

      Fuel Meter Operation

      Fuel gauge

      Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F

      Perform the test with the vehicle stopped and the engine idling.

      A/T Indicator Operation 1*2

      A/T indicator (normal mode)

      P, R, N, D, 4(M/S), 3(M/S), 2 or L

      Perform the test with the vehicle stopped and the engine idling.

      A/T Indicator Operation 2*2

      A/T indicator (sequential mode)

      Es, 7, 6, 5 or 8

      Perform the test with the vehicle stopped and the engine idling.

      A/T Indicator Operation 3*2

      A/T indicator

      D

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Airbag

      SRS warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Precrash*9

      PCS indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Driver Side Seat Belt

      Front seat belt warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp ABS

      ABS warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Charge

      CHARGE warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Slip

      SLIP indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Coolant Cool

      Engine coolant temperature COOL

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Coolant Hot

      Engine coolant temperature HOT

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Beam

      BEAM indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Tail

      TAIL indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Fr FOG*4

      FRONT FOG indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Rr FOG*5

      REAR FOG indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Fuel

      FUEL warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Tire Pressure Warning System*6

      Tire pressure warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. ECONO*2

      Eco driving indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Cruise*7

      Cruise main indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Lamp Brake

      Brake system warning light (red indicator)

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat GLOW*10

      GLOW indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. EPS

      EPS warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Master Warning

      Master warning light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. SET*7

      Cruise set indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. SIL (Up)*8

      SIL indicator (UP) light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. SIL (Down)*8

      SIL indicator (DOWN) light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. ASL*7

      Speed limiter indicator

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. Sport (CVT Sport)*2

      SPORT indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Indicat. VSC OFF

      VSC OFF indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Automatic High Beam Indicator*11

      Automatic high beam indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Stop and Start ON Indicator*3

      Stop and start indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Stop and Start OFF Indicator*3

      Stop and start cancel indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      LDA Control Indicator*12

      Lane departure alert indicator light

      ON / OFF

      Perform the test with the vehicle stopped and the engine idling.

      Meter Display 1

      All dots in multi-information display

      ALL

      Perform the test with the vehicle stopped and the engine idling.

      • *1:

        • The doors are locked automatically when performing the speedometer Active Test. This is a normal function.

        • The needle position should be within the acceptable range.

        • The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.

      • *2: for CVT

      • *3: w/ Stop and Start System

      • *4: w/ Front Fog Light

      • *5: w/ Rear Fog Light

      • *6: w/ Tire Pressure Warning System

      • *7: w/ Cruise Control System

      • *8: for Manual Transaxle

      • *9: w/ Pre-collision System

      • *10: for 1WW

      • *11: w/ Automatic High Beam System

      • *12: w/ Lane Departure Alert System