POWER WINDOW CONTROL SYSTEM Power Windows do not Operate Using All Window Switch

DTC Code DTC Name
Power Windows do not Operate Using All Window Switch

DESCRIPTION

The power windows operate by using the power window regulator master switch assembly or power window regulator switch assembly.

The power window regulator master switch assembly and power window regulator switch assembly connect the same power supply and ground lines.

WIRING DIAGRAM

B371209E01
B371209E02

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    1. Remove the power window regulator master switch assembly.

      Click here

    2. Inspect the power window regulator master switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

    1. for LHD

      1. Disconnect the 3G driver side junction block assembly connector.

      2. Disconnect the H5 power window regulator master switch assembly connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3G-8 - H5-2 (B)

        Always

        Below 1 Ω

        3G-8 or H5-2 (B) - Body ground

        Always

        10 kΩ or higher

    2. for RHD

      1. Disconnect the 3G driver side junction block assembly connector.

      2. Disconnect the G5 power window regulator master switch assembly connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3G-8 - G5-2 (B)

        Always

        Below 1 Ω

        3G-8 or G5-2 (B) - Body ground

        Always

        10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

    1. for LHD

      1. Disconnect the H5 power window regulator master switch assembly connector.

      2. B371208C05

        *a

        Front view of wire harness connector

        (to power window regulator master switch assembly)

        Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        H5-2 (B) - Body ground

        Ignition switch ON

        11 to 14 V

    2. for RHD

      1. Disconnect the G5 power window regulator master switch assembly connector.

      2. B371208C06

        *a

        Front view of wire harness connector

        (to power window regulator master switch assembly)

        Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        G5-2 (B) - Body ground

        Ignition switch ON

        11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

    Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)

    1. for LHD

      1. Disconnect the H5 power window regulator master switch assembly connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        H5-1 (E) - Body ground

        Always

        Below 1 Ω

    2. for LHD

      1. Disconnect the G5 power window regulator master switch assembly connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        G5-1 (E) - Body ground

        Always

        Below 1 Ω

    Result

    Proceed to

    OK

    NG
    OK

    USE SIMULATION METHOD TO CHECK

    Click hereClick hereClick here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR