FRONT LOWER SUSPENSION ARM(for 2AR-FE, 6AR-FSE LH Side) INSTALLATION

PROCEDURE


  1. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    1. Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.

    2. Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut.

    3. B0085GIC01
      *a Torque Wrench Fulcrum Length
      *b Ball Joint Lock Nut Wrench
      B008776 Turn

      Using a ball joint lock nut wrench, fully tighten the bolt (1).

      Torque:
      Specified tightening torque
      200 N*m  { 2039 kgf*cm, 148 ft.*lbf }

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):

        145.5 N*m (1484 kgf*cm, 107 ft.*lbf)

    4. Fully tighten the bolt (2) and then (3).

      Torque:
      Bolt (2)
      200 N*m  { 2039 kgf*cm, 148 ft.*lbf }
      Bolt (3)
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    5. Slowly lower the engine assembly with transaxle using a jack and a wooden block.

      Note


      • Do not position the wooden block under the oil pan.

      • Do not damage the components surrounding the engine assembly with transaxle.

      • Ensure that the jack and wooden block are stable.

    6. Connect the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. CONNECT FRONT ENGINE MOUNTING INSULATOR


    1. Connect the front engine mounting insulator to the front frame assembly with the 3 nuts.

      Torque:
      72 N*m  { 734 kgf*cm, 53 ft.*lbf }

  3. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    1. Connect the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly LH with the bolt and 2 nuts.

      Torque:
      92 N*m  { 938 kgf*cm, 68 ft.*lbf }

  4. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  5. INSTALL BATTERY

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  6. INSTALL AIR CLEANER ASSEMBLY

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  7. INSTALL FRONT FENDER APRON SEAL LH

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  8. INSTALL NO. 1 ENGINE UNDER COVER

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  9. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  10. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

    for 2AR-FE: Click here

    for 6AR-FSE: Click here

  11. INSTALL FRONT WHEEL

    Click here

  12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  13. PERFORM INITIALIZATION

    Parking assist monitor system

    for Initialization: Click here

    for Calibration: Click here

    Panoramic view monitor system

    for Initialization: Click here

    for Calibration: Click here

    Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System)

    Click here