LIGHTING SYSTEM Door Unlock Detection Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.

WIRING DIAGRAM

A01VTKME06

CAUTION / NOTICE / HINT

Note


  • Before replacing the main ECU (multiplex network body ECU), refer to Service Bulletin.

  • The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before proceeding with troubleshooting, perform an on-vehicle inspection and confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

    Click here


    • *: w/o Canister Pump Module with Door Ajar Warning Buzzer Function

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal ON or OFF

      ON: Rear door RH unlocked

      OFF: Rear door RH locked

      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal ON or OFF

      ON: Rear door LH unlocked

      OFF: Rear door LH locked

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      FR Door Lock Pos
      FL Door Lock Pos
      RR-Door Lock Pos SW
      RL-Door Lock Pos SW
      Result
      Result Proceed to
      OK A
      FL Door Lock Pos is not normal B
      FR Door Lock Pos is not normal C
      RL-Door Lock Pos SW is not normal D
      RR-Door Lock Pos SW is not normal E

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH Click here

    D

    INSPECT REAR DOOR LOCK ASSEMBLY LH Click here

    E

    INSPECT REAR DOOR LOCK ASSEMBLY RH Click here

    B

  2. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH


    1. Remove the front door lock with motor assembly LH.

      Click here

    2. Inspect the front door lock with motor assembly LH.

      Click here

      OK
      Front door lock with motor assembly LH is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)


    1. Disconnect the 2B instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Double Locking
      Tester Connection Condition Specified Condition
      N8-8 (LSSR) - 2B-13 Always Below 1 Ω
      N8-8 (LSSR) or 2B-13 - Body ground Always 10 kΩ or higher
      N8-7 (E) - Body ground Always Below 1 Ω
      w/ Double Locking
      Tester Connection Condition Specified Condition
      N8-10 (LSSR) - 2B-13 Always Below 1 Ω
      N8-10 (LSSR) or 2B-13 - Body ground Always 10 kΩ or higher
      N8-9 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01VTZJC09
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      MB-19 (LSFL) - 2B-13 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  5. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH


    1. Remove the front door lock with motor assembly RH.

      Click here

    2. Inspect the front door lock with motor assembly RH.

      Click here

      OK
      Front door lock with motor assembly RH is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)


    1. Disconnect the 2B instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Double Locking
      Tester Connection Condition Specified Condition
      M8-7 (LSSR) - 2B-12 Always Below 1 Ω
      M8-7 (LSSR) or 2B-12 - Body ground Always 10 kΩ or higher
      M8-8 (E) - Body ground Always Below 1 Ω
      w/ Double Locking
      Tester Connection Condition Specified Condition
      M8-5 (LSSR) - 2B-12 Always Below 1 Ω
      M8-5 (LSSR) or 2B-12 - Body ground Always 10 kΩ or higher
      M8-6 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01VTZJC10
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      MB-17 (LSFR) - 2B-12 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  8. INSPECT REAR DOOR LOCK ASSEMBLY LH


    1. Remove the rear door lock assembly LH.

      Click here

    2. Inspect the rear door lock assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR DOOR LOCK ASSEMBLY LH Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)


    1. Disconnect the 2B instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Double Locking
      Tester Connection Condition Specified Condition
      P3-6 (LSSR) - 2B-14 Always Below 1 Ω
      P3-6 (LSSR) or 2B-14 - Body ground Always 10 kΩ or higher
      P3-9 (E) - Body ground Always Below 1 Ω
      w/ Double Locking
      Tester Connection Condition Specified Condition
      P3-9 (LSSR) - 2B-14 Always Below 1 Ω
      P3-9 (LSSR) or 2B-14 - Body ground Always 10 kΩ or higher
      P3-10 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01VTZJC11
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      MB-5 (LSWL) - 2B-14 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  11. INSPECT REAR DOOR LOCK ASSEMBLY RH


    1. Remove the rear door lock assembly RH.

      Click here

    2. Inspect the rear door lock assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR DOOR LOCK ASSEMBLY RH Click here

    OK

  12. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)


    1. Disconnect the J9 main body ECU (multiplex network body ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Double Locking
      Tester Connection Condition Specified Condition
      O3-6 (LSSR) - J9-2 (LSWR) Always Below 1 Ω
      O3-6 (LSSR) or J9-2 (LSWR) - Body ground Always 10 kΩ or higher
      O3-9 (E) - Body ground Always Below 1 Ω
      w/ Double Locking
      Tester Connection Condition Specified Condition
      O3-5 (LSSR) - J9-2 (LSWR) Always Below 1 Ω
      O3-5 (LSSR) or J9-2 (LSWR) - Body ground Always 10 kΩ or higher
      O3-6 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR