ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | FUEL VAPOR FEED HOSE |
| *3 | INLET HEATER WATER HOSE | *4 | OUTLET HEATER WATER HOSE |
| *5 | UNION TO CONNECTOR TUBE HOSE | *6 | SUCTION HOSE SUB-ASSEMBLY |
| *7 | DISCHARGE HOSE SUB-ASSEMBLY | *8 | FUEL PIPE |
| *9 | O-RING | *10 | NO. 1 FUEL PIPE CLAMP |
| *11 | BATTERY CLAMP SUB-ASSEMBLY | *12 | NO. 1 RADIATOR HOSE |
| *13 | NO. 2 RADIATOR HOSE | *14 | NO. 2 CYLINDER HEAD COVER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil VC100YF or equivalent | - | - |
ILLUSTRATION
| *1 | FRONT FLOOR CENTER BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst) |
| *3 | COMPRESSION SPRING | *4 | EXHAUST PIPE GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH | *4 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
| *5 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *6 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *7 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | *8 | AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
| *9 | NO. 2 EARTH WIRE | *10 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | FAN AND GENERATOR V BELT | *2 | GENERATOR ASSEMBLY |
| *3 | FLYWHEEL HOUSING UNDER COVER | *4 | COMPRESSOR WITH PULLEY ASSEMBLY |
| *5 | WIRE HARNESS CLAMP BRACKET | *6 | ENGINE WIRE |
| *7 | TERMINAL CAP | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for Type A | *B | for Type B |
| *1 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *2 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT |
| *3 | ENGINE WIRE | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | STARTER ASSEMBLY | *6 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *7 | CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY | *8 | NO. 3 WATER BY-PASS HOSE |
| *9 | NO. 5 WATER BY-PASS HOSE | *10 | FRONT DRIVE PLATE SPACER |
| *11 | REAR DRIVE PLATE SPACER | - | - |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Adhesive 1324 |
| ★ | Precoated part | - | - |