POWER WINDOW REGULATOR MOTOR(for Sedan Rear Side) INSPECTION

PROCEDURE

  1. INSPECT REAR DOOR WINDOW REGULATOR ASSEMBLY LH

    CAUTION:

    Prevent any part of your body from being caught during inspection.

    1. B319644C01

      *a

      Component without harness connected

      (Rear Door Window Regulator Assembly LH)

      *b

      Up

      *c

      Down

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note:

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

    2. Connect a negative (-) battery to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

    3. Check that window regulator moves smoothly as follows:

      OK

      Measurement Condition

      Specified Condition

      1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery lead for terminal 10 (UP) within 1 second.

      Arm of window regulator rotates clockwise (Up)

      1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery lead for terminal 7 (DOWN) within 1 second.

      Arm of window regulator rotates counterclockwise (Down)

      • If the result is not as specified, replace the rear door window regulator assembly LH.

      Note:

      Initialize the power window control system after installing the rear door window regulator assembly LH.

  2. INSPECT REAR DOOR WINDOW REGULATOR ASSEMBLY RH

    CAUTION:

    Prevent any part of your body from being caught during inspection.

    1. B319646C01

      *a

      Component without harness connected

      (Rear Door Window Regulator Assembly RH)

      *b

      Up

      *c

      Down

      Apply positive (+) battery voltage to connector terminal 2 (B).

      Note:

      Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

    2. Connect a negative (-) battery to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

    3. Check that window regulator moves smoothly as follows:

      OK

      Measurement Condition

      Specified Condition

      1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery lead for terminal 10 (UP) within 1 second.

      Arm of window regulator rotates counterclockwise (Up)

      1. Connect a positive (+) battery lead to terminal 2 (B), connect the negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery lead for terminal 7 (DOWN) within 1 second.

      Arm of window regulator rotates clockwise (Down)

      • If the result is not as specified, replace the rear door window regulator assembly RH.

      Note:

      Initialize the power window control system after installing the rear door window regulator assembly RH.