REAR VIEW MONITOR SYSTEM(for Radio and Display Type) Reverse Signal Circuit

DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)

   1. 

      Enter the "Function Check/Setting I" mode and select "Vehicle Signal".

   2. Check that the display changes between ON and OFF according to the shift lever position.

      OK

      Shift Lever Position	Display
      R	ON
      Except R	OFF

      Tip:

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.

   Result

   Proceed to
   OK
   NG (except Manual Transaxle)
   NG (for Manuala Transaxle)

   OK

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

   Click here

   NG (for Manuala Transaxle)

   INSPECT BACK-UP LIGHT SWITCH ASSEMBLYClick here

   NG (except Manual Transaxle)

2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

   1. Remove the park/neutral position switch assembly.

      for U760E:

      Click here

      for U760F:

      Click here

      for U660F:

      Click here

      for K111:

      Click here

      for K111F:

      Click here

      for K114:

      Click here

      for K114F:

      Click here

   2. Inspect the park/neutral position switch assembly.

      for U760E:

      Click here

      for U760F:

      Click here

      for U660F:

      Click here

      for K111:

      Click here

      for K111F:

      Click here

      for K114:

      Click here

      for K114F:

      Click here

   Result

   Proceed to
   OK
   NG

   NG

   REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

   for U660F

   Click here

   for U760E

   Click here

   for U760F:

   Click here

   for K111

   Click here

   for K111F:

   Click here

   for K114:

   Click here

   for K114F:

   Click here

   OK

3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY AND BATTERY)

   1. Disconnect the B36*1 or B101*2 park/neutral position switch assembly connector.

      • *1: except 3ZR-FE, 2AR-FE

      • *2: for 3ZR-FE, 2AR-FE

   2. Disconnect the G143 radio and display receiver assembly connector.

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Table 1. except 3ZR-FE, 2AR-FE

      Tester Connection	Switch Condition	Specified Condition
      B36-1 (RB) - Body ground	Ignition switch ON	11 to 14 V

      Table 2. for 3ZR-FE, 2AR-FE

      Tester Connection	Switch Condition	Specified Condition
      B101-1 (RB) - Body ground	Ignition switch ON	11 to 14 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 3. except 3ZR-FE, 2AR-FE

      Tester Connection	Condition	Specified Condition
      B36-2 (RL) - G143-2 (REV)	Always	Below 1 Ω
      B36-2 (RL) - Body ground	Always	10 kΩ or higher

      Table 4. for 3ZR-FE, 2AR-FE

      Tester Connection	Condition	Specified Condition
      B101-2 (RL) - G143-2 (REV)	Always	Below 1 Ω
      B101-2 (RL) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   OK

   REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

   Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

4. INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

   1. Remove the back-up light switch assembly.

      for EA64:

      Click here

      for EA64F:

      Click here

      for EB61:

      Click here

      for EB61F:

      Click here

      for EB63F:

      Click here

      for EB63:

      Click here

   2. Inspect the back-up light switch assembly.

      for EA64:

      Click here

      for EA64F:

      Click here

      for EB61:

      Click here

      for EB61F:

      Click here

      for EB63F:

      Click here

      for EB63:

      Click here

   Result

   Proceed to
   OK
   NG

   NG

   REPLACE BACK-UP LIGHT SWITCH ASSEMBLY

   for EA64:

   Click here

   for EA64F:

   Click here

   for EA61:

   Click here

   for EA61F:

   Click here

   for EA63F:

   Click here

   for EB63:

   Click here

   OK

5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY AND BATTERY)

   1. Disconnect the B35*1 or C14*2 back-up light switch assembly connector.

      • *1: except 2WW

      • *2: for 2WW

   2. Disconnect the G143 radio and display receiver assembly connector.

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Table 5. except 2WW

      Tester Connection	Switch Condition	Specified Condition
      B35-2 - Body ground	Ignition switch ON	11 to 14 V

      Table 6. for 2WW

      Tester Connection	Switch Condition	Specified Condition
      C14-2 - Body ground	Ignition switch ON	11 to 14 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 7. except 2WW

      Tester Connection	Condition	Specified Condition
      B35-1 - G143-2 (REV)	Always	Below 1 Ω
      B35-1 - Body ground	Always	10 kΩ or higher

      Table 8. for 2WW

      Tester Connection	Condition	Specified Condition
      C14-1 - G143-2 (REV)	Always	Below 1 Ω
      C14-1 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   OK

   REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

   Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR