BLACK OUT TAPE(for Rear Door) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time maybe required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR TRIM COVER LH

    Click here

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  8. REMOVE REAR DOOR ARMREST SET BRACKET LH

    Click here

  9. REMOVE REAR DOOR SERVICE HOLE COVER LH

    Click here

  10. REMOVE REAR DOOR GLASS RUN LH

    Click here

  11. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

    Click here

  12. REMOVE REAR DOOR REAR GUIDE SEAL LH

    Click here

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  14. DISCONNECT REAR DOOR CHECK ASSEMBLY LH


    1. B008HGU

      Remove the bolt and disconnect the rear door check assembly LH.

  15. REMOVE REAR DOOR WEATHERSTRIP LH

    Click here

  16. REMOVE REAR DOOR FRAME GARNISH LH

    Click here

  17. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  18. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  19. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

    Click here

  20. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING LH

    Click here

  21. REMOVE NO. 1 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 1 black out tape LH, heat the rear door panel and No. 1 black out tape LH using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    No. 1 Black Out Tape LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or No. 1 black out tape LH excessively.


    1. B008I10

      Pull back an edge of the No. 1 black out tape LH and pull it parallel to the rear door panel to remove it.

  22. REMOVE NO. 2 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 2 black out tape LH, heat the rear door panel and No. 2 black out tape LH using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    No. 2 Black Out Tape LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or No. 2 black out tape LH excessively.


    1. B008HEX

      Pull back an edge of the No. 2 black out tape LH and pull it parallel to the rear door panel to remove it.

  23. REMOVE NO. 3 BLACK OUT TAPE LH

    Tech Tips

    When removing the No. 3 black out tape LH, heat the rear door panel and No. 3 black out tape LH using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    No. 3 Black Out Tape LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or No. 3 black out tape LH excessively.


    1. B008IAF

      Pull back an edge of the No. 3 black out tape LH and pull it parallel to the rear door panel to remove it.