TELEMATICS SYSTEM OPERATION CHECK

  1. ENTER TEST MODE

    Tip:

    • By performing a test call, it is possible to check the operation of the telematics transceiver.

    • Make sure to performe a test call after troubleshooting the telematics system.

    • Depending on radio wave signal conditions and the test center condition, a test call may fail even though the vehicle is not malfunctioning.

    1. Enter test mode by using either of the following methods:

    2. Method 1 (Recommended)

      1. Turn the ignition switch to ON and wait for 60 seconds with the vehicle stopped.

      2. Operate the light control switch as follows: Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail →Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail.

        Tip:

        • Turn the light control switch between Off and Tail at an interval of 10 seconds or less.

        • For vehicles without an Off position on the light control switch: Turn the light control switch to the AUTO position and cover and uncover the automatic light control sensor to turn the taillights on and off.

      3. E338332C01

        *a

        Manual (SOS) Switch Green Indicator

        *b

        Manual (SOS) Switch Red Indicator

        Check that the manual (SOS) switch indicators begin blinks 5 times over 10 seconds and then turn off. Push the manual (SOS) switch for less than 3 seconds within 15 seconds after the indicators begin to blink to enter test mode.

    3. Method 2

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Telematics / Utility / Emergency Call Check

        Body Electrical > Telematics > Utility

        Tester Display

        Emergency Call Check

      5. According to the display on the GTS, perform Emergency Call Check to enter test mode.

  2. PERFORME TEST CALL

    1. Enter test mode.

      Tip:

      The manual (SOS) switch indicator (green) will blink 3 times to indicate that test mode has been entered.

    2. Speak into the telephone microphone assembly and confirm that your voice can be heard from the speakers, and then press the manual (SOS) switch for 3 seconds or less to enter test call mode.

      Tip:

      • If your voice cannot be heard from the speakers, press and hold the manual (SOS) switch for 3 to 10 seconds.

      • The manual (SOS) switch indicator (green) will blink 4 times.

    3. Press the manual (SOS) switch and check that the manual (SOS) switch indicator (green) blinks 1 time. A test call will be performed and test data will be transmitted.

      Tip:

      • The manual (SOS) switch indicator (green) will illuminate for 10 seconds if test data transmission was successful.

      • The manual (SOS) switch indicator (red) will illuminate for 10 seconds if test data transmission fails.

  3. DCM Operation History

    Tip:

    This function is used to display operation history information and the time at which it was stored in the telematics transceiver.

    1. Check DCM Operation History

      Tip:

      When problem symptoms due to wave interference cannot be reproduced, this function provides telematics transceiver operation history information which can be used to explain the cause of the malfunction to the customer.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History

        Body Electrical > Telematics > Utility

        Tester Display

        DCM Operation History

        Item

        Function

        Parameter Name

        Operation History

        Displays the result of an attempt emergency call.

        Success

        Fail

        Activation Failed

        Displays the reason for failure if communication failed.

        Unrecognized VIN

        Unrecognized DCM-ID

        Unrecognized IMSI

        Unavailable Service Center

        Service Already Activated

        Backup Battery Status

        Displays the mobilephone battery condition.

        Low Battery Amount

        Low Battery Voltage

        Battery Exhaustion

        Abnormal