MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) INSTALLATION

CAUTION / NOTICE / HINT

Note

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.

PROCEDURE


  1. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY


    1. Coat a new O-ring with gear oil.

    2. Install the O-ring to the speedometer driven hole cover sub-assembly.

    3. Install the speedometer driven hole cover sub-assembly to the manual transaxle assembly with the bolt.

      Torque:
      11.3 N*m  { 115 kgf*cm, 8 ft.*lbf }

  2. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

    2. Connect the clamp to the No. 1 transmission control cable bracket.

  3. INSTALL CONTROL CABLE BRACKET ASSEMBLY


    1. Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  4. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the manual transmission case with the bolt.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

  5. INSTALL NO. 1 HEATER BRACKET SUB-ASSEMBLY


    1. Install the No. 1 heater bracket sub-assembly to the manual transmission case with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  6. INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

    Click here

  7. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    Click here

  8. INSPECT CLUTCH PIPE LINE

    Click here

  9. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    Click here

  10. INSTALL CLUTCH FLEXIBLE HOSE BRACKET


    1. Install the clutch flexible hose bracket to the manual transaxle assembly with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  11. INSTALL BLEEDER CLUTCH RELEASE TUBE

    Click here

  12. INSTALL MANUAL TRANSAXLE ASSEMBLY


    1. B008LHYC01
      *1 Knock Pin

      Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.

    2. Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.

      Note


      • Make sure that the wire harness or similar items are not pinched between the contact surfaces.

      • Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.

      • Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

      • Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.

      • Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.

    3. B008LGME02

      Temporarily install the bolt (A).

    4. Install the bolt (B), then fully tighten the bolt (A).

      Torque:
      for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

    5. Install the 5 bolts.

      Torque:
      for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }
    6. B008LN7C01
      *a Temporarily Tighten

      Install the engine mounting bracket LH to the manual transaxle assembly with the 5 bolts in the order shown in the illustration.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

    7. Engage the hook to temporarily install the engine mounting insulator LH to the vehicle body.

    8. B008LKNC01
      *a Temporarily Tighten

      Install the nut and 4 bolts in the order shown in the illustration.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    9. Install the transverse engine engine mounting insulator to the engine mounting bracket LH with the bolt and nut.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

      Tech Tips

      Turn the bolt while holding the nut.

  13. INSTALL FLYWHEEL HOUSING SIDE COVER

    Click here

  14. INSTALL STARTER ASSEMBLY (for Cold Area Specification Vehicles)

    Click here

  15. INSTALL STARTER ASSEMBLY (except Cold Area Specification Vehicles)

    Click here

  16. INSTALL NO. 2 ENGINE MOVING CONTROL ROD


    1. B008LO6C01
      *a Temporarily Tighten

      Install the No. 2 engine moving control rod to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  17. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here

  18. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

    Click here

  19. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

    Click here

  20. REMOVE ENGINE SUPPORT BRIDGE


    1. Remove SST from the vehicle body.

      Note

      Prevent SST from contacting the vehicle body or windshield glass.

    2. Install the neck from the windshield washer jar assembly with the clip.

  21. REMOVE ENGINE HANGER


    1. Remove the 2 bolts and No. 2 engine hanger from the cylinder head.

    2. Remove the 2 bolts and No. 1 engine hanger from the cylinder head.

    3. Connect the No. 2 earth wire to the engine mounting insulator sub-assembly RH with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

    5. Install the engine wire to the wire harness clamp bracket with the nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    6. Engage the 3 clamps with the wire harness clamp bracket.

    7. Connect the wire harness to the wire harness clamp bracket.

  22. INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

    Click here

  23. INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

    Click here

  24. INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

    Click here

  25. CONNECT NO. 1 CLUTCH HOSE


    1. Connect the No. 1 clutch hose and install a new clip to the No. 1 clutch hose.

      Note

      Install the clip as far as it will go.

    2. B008LAPC01
      *a Torque Wrench Fulcrum Length

      Using a 10 mm union nut wrench, install the bleeder clutch release tube to the No. 1 clutch hose.

      Torque:
      Specified Tightening Torque
      15.2 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not kink or damage the No. 1 clutch hose.

      • Do not allow any foreign matter such as dirt or dust to enter the No. 1 clutch hose from the clip or bracket.

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

  26. CONNECT WIRE HARNESS


    1. Engage the 3 clamps and install the wire harness to the manual transaxle assembly.

    2. Connect the neutral position switch connector.

    3. Engage the 3 clamps and install the heated oxygen sensor wire harness to the front suspension crossmember sub-assembly.

    4. Engage the clamp and install the wire harness to the manual transaxle assembly.

    5. Install the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

    6. Connect the transmission revolution sensor connector.

    7. Connect the back-up light switch assembly connector.

  27. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

    Click here

  28. INSTALL FRONT FLOOR CENTER BRACE

    Click here

  29. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

    Click here

  30. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  31. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  32. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here

  33. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B008L2EC02
      *a Paint Mark

      Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips B.

      Note

      Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.

    2. Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips A.

  34. INSTALL BATTERY CLAMP SUB-ASSEMBLY


    1. Install the battery clamp sub-assembly to the vehicle with the 3 bolts.

      Torque:
      15.4 N*m  { 157 kgf*cm, 11 ft.*lbf }

    2. Engage the clamp to connect the engine wire to the battery clamp sub-assembly.

    3. Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  35. INSTALL ECM

    Click here

  36. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  37. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  38. INSTALL NO. 1 AIR CLEANER INLET

    Click here

  39. INSTALL RADIATOR COVER

    Click here

  40. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

    Click here

  41. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  42. INSTALL COWL BODY MOUNTING REINFORCEMENT RH

    Click here

  43. INSTALL COWL BODY MOUNTING REINFORCEMENT LH

    Click here

  44. INSTALL WATER GUARD PLATE LH

    Click here

  45. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

    Click here

  46. INSTALL WINDSHIELD WIPER MOTOR AND LINK

    Click here

  47. INSTALL FRONT WHEELS

    Click here

  48. INSTALL BATTERY

    Click here

  49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  50. ADD MANUAL TRANSAXLE OIL

    Click here

  51. BLEED CLUTCH LINE

    Click here

  52. INSPECT MANUAL TRANSAXLE OIL

    Click here

  53. INSPECT FOR MANUAL TRANSAXLE OIL LEAK

  54. INSPECT FOR EXHAUST GAS LEAK

    Click here

    Tech Tips

    Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

    Click here

  55. INSTALL FRONT FLOOR COVER LH (w/ Cover)

    Click here

  56. INSTALL FRONT FLOOR COVER RH (w/ Cover)

    Click here

  57. INSTALL REAR ENGINE UNDER COVER RH

    Click here

  58. INSTALL REAR ENGINE UNDER COVER LH

    Click here

  59. INSTALL NO. 1 ENGINE UNDER COVER

    Click here

  60. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here