REAR BRAKE REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Click here

  2. PERFORM REAR BRAKE PAD REPLACEMENT MODE

    Click here

  3. REMOVE REAR WHEEL

    Click here

  4. DRAIN BRAKE FLUID

    Note

    If brake fluid leaks onto any painted surface, immediately wash it off.

  5. SEPARATE REAR FLEXIBLE HOSE


    1. B005MBN

      Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.

  6. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY


    1. B007X2S

      Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

      Note


      • Remove any dirt or foreign matter on and around the connector before performing this work.

      • Do not allow water, oil or dirt to enter the connector.

  7. REMOVE PARKING BRAKE ACTUATOR ASSEMBLY


    1. B0010DX

      Using a 5 mm hexagon socket wrench, remove the 2 bolts and parking brake actuator assembly from the rear disc brake cylinder assembly.

      Note


      • Check that there are no brake fluid leaks from the back of the rear disc brake cylinder assembly.

      • If there are any brake fluid leaks, replace the rear disc brake cylinder assembly.

    2. Remove the O-ring from the rear disc brake cylinder assembly.

  8. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    1. B0010SMC02
      *a Turn
      *b Hold

      Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.

  9. REMOVE REAR DISC BRAKE PAD


    1. B005LOU

      Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

  10. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM


    1. B0010NOC03
      *1 Rear No. 1 Disc Brake Anti-squeal Shim
      *2 Rear No. 2 Disc Brake Anti-squeal Shim
      *3 Rear Disc Brake Pad Wear Indicator Plate

      Remove the rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (inside).

    2. Remove the rear No. 1 disc brake anti-squeal shim from the rear disc brake pad (inside).

    3. Remove the rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (outside).

    4. Remove the rear No. 1 disc brake anti-squeal shim from the rear disc brake pad (outside).

    5. Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.

  11. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    1. B0010HB

      Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

      Note

      Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

  12. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN


    1. B005OXVC02
      *1 Rear No. 1 Disc Brake Cylinder Slide Pin
      *2 Rear No. 2 Disc Brake Cylinder Slide Pin

      Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.

    2. B0010MTC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

      Note

      Do not damage the rear No. 2 disc brake cylinder slide pin.

  13. REMOVE REAR DISC BRAKE BUSHING DUST BOOT


    1. B0010HN

      Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.

  14. REMOVE REAR DISC BRAKE CYLINDER MOUNTING


    1. B0010MX

      Remove the 2 bolts and rear disc brake cylinder mounting.

  15. REMOVE REAR DISC


    1. B005LP1C02
      *a Matchmark

      Put matchmarks on the rear disc and rear axle hub and bearing assembly.

    2. Remove the rear disc.