FRONT SEAT SIDE AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Removal/installation of the front passenger seat*1 Zero point calibration (Occupant classification system)

  • Occupant classification system

  • Passenger airbag ON/OFF indicator

  • Airbag system (Front passenger side)

  • Seat belt warning system (Front passenger)

Click here

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

*1: w/ Occupant Classification System

CAUTION:

B0084N2

  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

for Manual Seat: Click here

for Power Seat: Click here

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

    Click here

  3. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)

    Click here

  4. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)

    Click here

  5. REMOVE VERTICAL ADJUSTING HANDLE (for Manual Seat)

    Click here

  6. REMOVE RECLINING HINGE COVER (for Manual Seat)

    Click here

  7. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

    Click here

  8. REMOVE SEAT ADJUSTER COVER CAP (for Manual Seat)

    Click here

  9. REMOVE FRONT SEAT FRONT CUSHION SHIELD (for Power Seat)

    Click here

  10. REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)

    w/o Vertical Adjuster: Click here

    w/ Vertical Adjuster: Click here

  11. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

    Click here

  12. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)

    w/o Vertical Adjuster: Click here

    w/ Vertical Adjuster: Click here

  13. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)

    Click here

  14. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)

    Click here

  15. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)

    Click here

  16. REMOVE FRONT SEAT HEADREST SUPPORT (for Power Seat)

    Click here

  17. REMOVE FRONT SEAT HEADREST SUPPORT (for Manual Seat)

    Click here

  18. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)

    Click here

  19. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)

    Click here

  20. REMOVE FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:

    When storing the front seat airbag assembly, keep the airbag deployment side facing upward.

    B0083S4C02
    B0087TV Deployment Side

    1. B0087NF

      for Power Seat Type A:


      1. Disengage the clamp.

      2. Remove the 2 nuts and front seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.

    2. B0083YO

      for Power Seat Type B, Manual Seat:


      1. Disengage the clamp.

      2. Remove the 2 nuts and front seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.