HEADLIGHT ASSEMBLY (for LED Headlight) ADJUSTMENT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT


    1. Prepare the vehicle:


      • Make sure that there is no damage to the body around the headlights.

      • Fill the fuel tank.

      • Make sure that the oil is filled to the specified level.

      • Make sure that the coolant is filled to the specified level.

      • Inflate the tires to the appropriate pressure.

      • Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

      • Have a person of average weight (75 kg, 165 lb) sit in the driver seat.

  2. PREPARATION FOR HEADLIGHT AIMING

    B007OWWE01
    Text in Illustration
    *a 25 or 3 m

    1. Prepare the vehicle.


      • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

      • Place the vehicle at a 90° angle to the wall.

      • B007R6DE01
        Text in Illustration
        *a High Beam Center Mark
        *b Low Beam Center Mark

        Create a 25 m (82 ft.) distance between the vehicle (headlight center mark) and the wall.

      • Make sure that the vehicle is on a level surface.

      • Bounce the vehicle up and down to settle the suspension.

      Note

      A distance of 25 m (82 ft.) between the vehicle (headlight center mark) and wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment (the target zone will change with the distance, so follow the instructions in the illustration).

    2. Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.

    3. Draw a vertical line down the center of the screen (V line).

    4. Set the screen as shown in the illustration.

      Tech Tips


      • Stand the screen perpendicular to the ground.

      • Align the V line on the screen with the center of the vehicle.

      B007QZ7E01
    5. B007P93E01
      Text in Illustration
      *a V LH Line
      *b V Line
      *c V RH Line
      *d H Line
      *e Ground

      Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

      Tech Tips

      Mark the headlight center marks on the screen.


      1. H Line (Headlight height):

        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight center marks of the low beam headlights.

      2. V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

        Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlights).

  3. INSPECT HEADLIGHT AIMING


    1. Cover the headlight on the opposite side to prevent light from the headlight not being inspected from affecting headlight aiming inspection.

      Note

      Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

    2. Start the engine.

    3. Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

      Tech Tips


      • The low beam and high beam headlight are a unit. Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

      • If the alignment distance is 25 m (82 ft.):

        The low beam cutoff line should be within 83 mm (3.2677 in.) and 375 mm (1.23 ft.) below the H line as well as 250 mm (9.8425 in.) left or right of the V LH or V RH line.

      • If the alignment distance is 3 m (9.84 ft.):

        The low beam cutoff line should be within 10 mm (0.3937 in.) and 45 mm (1.7717 in.) below the H line as well as 30 mm (1.1811 in.) left or right of the V LH or V RH line.

      • If the alignment distance is 25 m (82 ft.):

        The horizontal line of the preferred low beam cutoff line is 250 mm (9.8425 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      • If the alignment distance is 3 m (9.84 ft.):

        The horizontal line of the preferred low beam cutoff line is 30 mm (1.1811 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

      • If the alignment distance is 25 m (82 ft.):

        The high beam center of intensity should be within 175 mm (6.8898 in.) above and 250 mm (9.8425 in.) below the H line as well as 500 mm (1.64 ft.) left or right of the V LH or V RH line.

      • If the alignment distance is 3 m (9.84 ft.):

        The high beam center of intensity should be within 21 mm (0.8268 in.) above and 30 mm (1.1811 in.) below the H line as well as 60 mm (2.3622 in.) left or right of the V LH or V RH line.

      B007RGUE01

  4. ADJUST HEADLIGHT AIMING

    B007RLDE02
    Text in Illustration
    *a Screwdriver
    *b Vertical Aiming
    *c Horizontal Aiming

    1. Using a screwdriver, adjust the aim.

      Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

      Note

      The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.