POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)

CAUTION / NOTICE / HINT

PROCEDURE

1. VEHICLE BROUGHT TO WORKSHOP

   Result

   Proceed to
   NEXT

   NEXT

2. CUSTOMER PROBLEM ANALYSIS

   Tip:

   • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

   • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

   • The following 5 items are important points for problem analysis:

     What	Vehicle model, system name
     When	Date, time, occurrence frequency
     Where	Road conditions
     Under what conditions?	Driving conditions, weather conditions
     How did it happen?	Problem symptoms

   Result

   Proceed to
   NEXT

   NEXT

3. INSPECT BATTERY VOLTAGE

   1. Measure the battery voltage.

      Standard voltage

      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

   NEXT

4. INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

   1. Use the GTS to check if the LIN communication system is functioning normally.

      Click here

   Result

   Proceed to
   DTCs are not output
   DTCs are output

   DTCs are output

   GO TO LIN COMMUNICATION SYSTEM

   Click hereClick here

   DTCs are not output

5. CHECK FOR DTC*

   1. Check for DTCs and make a note of any codes that are output.

      Click here

      Body Electrical > D-Door Motor > Trouble Codes

   2. Clear the DTCs.

      Click here

      Body Electrical > D-Door Motor > Clear DTCs

   3. Recheck for DTCs.

      Click here

      Body Electrical > D-Door Motor > Trouble Codes

   Result

   Proceed to
   DTCs are not output
   DTCs are output

   DTCs are output

   GO TO DIAGNOSTIC TROUBLE CODE CHART

   Click here

   DTCs are not output

6. PROBLEM SYMPTOMS TABLE

   1. Refer to Problem Symptoms Table.

      Click hereClick here

   Result

   Proceed to
   Fault is not listed in problem symptoms table
   Fault is listed in problem symptoms table

   Fault is listed in problem symptoms table

   ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

   Fault is not listed in problem symptoms table

7. OVERALL ANALYSIS AND TROUBLESHOOTING*

   1. Operation Check

      Click hereClick here

   2. Terminals of ECU

      Click here

   3. Data List / Active Test

      Click here

   4. Fail-safe Chart

      Click hereClick here

   Result

   Proceed to
   NEXT

   NEXT

8. ADJUST, REPAIR OR REPLACE

   1. Check if the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD), door glass or door glass run has been removed and reinstalled.

   Result

   Result	Proceed to
   Front power window regulator motor assembly LH (for LHD), front power window regulator motor assembly RH (for RHD), door glass or door glass run has been removed and reinstalled.	A
   Front power window regulator motor assembly LH (for LHD), front power window regulator motor assembly RH (for RHD), door glass or door glass run has not been removed and reinstalled.	B

   B

   CONFIRMATION TESTClick here

   A

9. INITIALIZE POWER WINDOW CONTROL SYSTEM

   1. If the front door window regulator assembly (for driver door) has been removed and reinstalled, perform "Initialize Power Window Control System" for the driver door glass.

      Click hereClick here

      Tip:

      If "Initialize Power Window Control System" has not been performed, the auto operation function, jam protection function and key-off operation function will not operate or will operate incorrectly.

   Result

   Proceed to
   NEXT

   NEXT

10. CONFIRMATION TEST

    Result

    Proceed to
    NEXT

    NEXT

    END